Hour Meter; Squeegee Assembly; Adjustment Of The Squeegee; Splash Guard Assembly - ADIATEK sapphire 65 Emploi Et Entretien

GB
3. When the writing begins to blink, take off the
fingers from the push buttons and press once the
push button (6).
4. The writing GE36 appears blinking.
5. When the writing stops to blink, the setting is
modified.
For the passage of the setting from gel batteries into
lead batteries, repeat the procedure pressing button
(3) instead of button (6).
ATTENTION:
As the machine is 36V version, do not set the batter-
ies at 24V.

HOUR METER

The machine is equipped with an hour meter located
on the same display (1) of the battery charge level
indicator. Keeping the button (13) pressed, the first
data indicates the working hours and after a few se-
conds the working minutes are shown.

SQUEEGEE ASSEMBLY

1. Maintain the squeegee support (1) slightly lifted
from the floor.
2. Insert the threaded parts of the two knobs (4)
making them slide inside the two slots on the sup-
port placed on the upper part of the squeegee (2).
3. Place the washers (3), they are two for each knob,
so that they are assembled one under and the other
on each of the two slots present on the support.
4. Block the squeegee by rotating the two knobs (4)
clockwise.
5. Insert the squeegee hose (5) into its coupling, re-
specting its position as indicated in the figure.

ADJUSTMENT OF THE SQUEEGEE

In order to have a perfect drying result through the
squeegee, the rear rubber must have the lower bend-
ing uniformly adjusted in all its length. For the ad-
justment, it is necessary to put oneself in working
condition and therefore the suction motor has to be
switched on and the brushes have to function to-
gether with the detergent solution.
The lower part of the rubber is too much bent
Take off the pressure rotating the wing nut (6) coun-
terclockwise.
The lower part of the rubber is not much bent
Increase the pressure rotating the wing nut (6)
clockwise. Check that the wheels which adjust the
height do not rest on the floor, in this case adjust
them as indicated in paragraph "Height adjustment".
The bending is not uniform
Adjust the squeegee inclination rotating counter-
clockwise the wing nut (7) to increase the bending in
the central part, or clockwise to increase the bending
on the extremities.
Height adjustment
Once that the pressure and inclination of the squee-
gee have been adjusted, it is necessary to fix this op-
timum condition making touch slightly the wheels
onto the floor. Rotate clockwise the registers (8) to
lower the wheels or counterclockwise to raise them.
Both wheels must be adjusted in the same measure.
ATTENTION:
Every type of floor requires a specific adjustment.
For example, concrete floors (where the friction re-
sults to be high) need little pressure, while smooth
floors (ceramics) need higher pressure.
If the cleaning operations are made always on the
same type of floor, the adjustment can change only
in function of the rubber wear.

SPLASH GUARD ASSEMBLY

(sapphire 65)
The two splash guards have to be assembled onto the
brushes base group as indicated in the following fig-
ures. Insert the metal strips inside the suitable slots
present on the rubber. Place the round hole at the
flat extremity of the strip onto the pin (1) placed in
the front part of the brushes base group. Secure the
strips through the nut blocking it.
Block the coupling lever (2) in the rear part of the
brushes base group to the ring placed at the extrem-
ity of the metal strip still free. Please act as above
for both splash guard rubbers.
With the brushes assembled, the splash guard must
slightly touch the floor.
23
For the disassembly it is necessary to proceed in-
versely with above-mentioned operations.
(sapphire 85)
The two splash guards have to be assembled onto the
brushes base group. Insert the metal strips inside the
suitable slots present on the rubber. Place the round
hole at the flat extremity of the strip onto the pins
placed in the rear part of the brushes base group.
Secure the strips through the nuts (1) blocking them.
Block the coupling lever (2) in the front part of the
brushes base group to the ring placed at the extrem-
ity of the metal strips still free. Please act as above
for both splash guard rubbers.
With the brushes assembled, the splash guard must
slightly touch the floor.
For the disassembly it is necessary to proceed in-
versely with above-mentioned operations.
GB