Water Supply Line Connection - DENTSPLY Cavitron Select SPS Instructions D'utilisation

Section 6: Installation Instructions for Cavitron

6.6 Water Supply Line Connection

• Push the blue hose into the orange water receptacle until the
hose cannot be pushed in any further.
• Connect the free end of the system's water supply line to the
oice water supply line.
• Inspect all connections to make certain there are no leaks.
• To remove water line from Cavitron ® Select™ SPS™ Scaler,
turn of or disconnect water supply line FIRST, then push
on outer orange ring of the outlet and gently pull out
water hose.
6.7 Lavage Control Detachable
Handpiece Cable Assembly
Connection
• Plug the Handpiece outlet into the receptacle on the back of
the System.
• Holding the Handpiece Cable Assembly seat male connector
into appropriate female connector.
• Once seated, snap male connector into female connector by
pushing on the end of the male connector.
• Rotate Lavage Control on the handpiece to middle setting.
• Turn on the on/of switch (power adjustment).
ENGLISH • 6
Select™ SPS™ Ultrasonic Scaler, cont'd
®
Section 7: Installation Instructions for Cavitron
SPS™ Scaler with Cavitron Select™ Reservoir System
®
7.1 Water Line Requirements
See Section 6.1.
7.2 Electrical Requirements
See Section 6.2.
7.3 Unpacking the System
Carefully unpack your Cavitron ® Select™ SPS™ Scaler and verify
that all components and accessories are included:
1. Cavitron ® Select™ SPS™ Scaler.
2. Cavitron ® Select™ Reservoir Pump.
3. Cavitron ® Select™ Reservoir Bottle.
4. Detachable AC Power Cord set.
5. Steri-Mate Detachable Sterilizable Handpiece.
6. Steri-Mate Flow Control Detachable Handpiece
Cable Assembly with Swivel.
7. Dual Position Foot Control Assembly.
8. Hose / Filter / Quick Disconnect Assembly.
9. Additional Water Line Filter.
10. Additional Pump Lavage Filters.
11. Medically Approved Power Supply.
12. Literature Packet.
13. Cavitron Ultrasonic Insert (quantity optional).
7.4 Assembling the System
• Remove protective sticker from edge card connector on the scaler.
• Rinse Cavitron ® Select™ Reservoir Bottle before using.
• Insert Cavitron ® Select™ Reservoir Bottle into Cavitron
Select™ Reservoir Pump and rotate clockwise until bottle
locks into place.
Select™
®
• Connect Cavitron ® Select™ SPS™ Scaler to Cavitron
Reservoir System. Insert male edge card connector on Cavi-
tron ® Select™ Reservoir Pump into Cavitron
Scaler opening on the back of the Cavitron
Scaler. Press down on the top of the
Cavitron ® Select™ SPS™ Scaler (directly above power
setting knob) until the black striker knob located on the
Reservoir Bottle locks into place.
• To detach Cavitron ® Select™ SPS™ Scaler from Cavitron
Select™ Reservoir Pump and Bottle, lift up on the front of
the Cavitron Select™ SPS™ Scaler (below power setting knob
®
and Power/Boost light). After the striker knob is unsnapped,
pull the Cavitron ® Select™ SPS™ Scaler away from the Cavit-
ron ® Select™ Reservoir Pump.
®
NOTE: Always disengage striker knob before pulling theCa-
vitron ® Select™ SPS™ Scaler away from the Cavitron
Reservoir Pump.
® Select™
® SPS™ Select™
® Select™ SPS™
®
® Select™
ENGLISH • 7