Configuration Angle Zéro; 2Ème Mode - Huvema HU 440 BMSY DGH Manuel D'utilisation

7. c
onfiGuraTion anGle zéro
7.1 a
ANGLE ZERO SET
fficHaGe confiGuraTion zéro pour Tcs
Avant d'adopter la configuration zéro, l'arc doit êter en position haute.
1. Appuyer sur le bouton « configurer » dans un laps de temps de 10 secondes..
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON. 2. « P00 » s'affichera
3. Appuyer sur le bouton « ∆ » et atteindre « p09 ».
ANGLE ZERO SET
1. PRESS "SET" BUTTON İN 10 SECOND.
Appuyer sur le bouton « . » et puis sur le bouton « ∆ »
4.
2. IT WİLL APPEAR "P00" ON THE DİSPLAY
5. Le paramètre p09 sera sur « oui »
3. PRESS "∆" BUTTON UNTİL "P09".
6. Déplacer la structure jusqu'à voir s'afficher +60,0 ou -60,0 degrés (peu importe lequel des deux).
4.
7. Lorsque 60 degrés s'affiche, verrouiller l'arc.
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
5. PARAMETER P09 WİLL BE "YES"
8. Lorsque l'on appuie sur le bouton « reset », « 000,0 » s'affiche à l'écran.
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
1. PRESS "SET" BUTTON İN 10 SECOND.
9. Tourner l'arc jusqu'à voir s'afficher +60,0 ou -60,0 degrés.
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
2. IT WİLL APPEAR "P00" ON THE DİSPLAY
10. Verrouiller de nouveau l'arc.
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
3. PRESS "∆" BUTTON UNTİL "P09".
11. Lorsque l'on appuie sur le bouton « reset », « 000,0 » s'affiche à l'écran.
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
4.
12. Continuer de nr.1 À nr.5 Pour que p09 soit sur « non »
10. LOCK THE BOW AGAİN.
5. PARAMETER P09 WİLL BE "YES"
13. Appuyer sur « configurer » pour sortir du menu des paramètres.
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
7.2 2è
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
me mode
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
1 Appuyer sur le bouton
2.WAY
10. LOCK THE BOW AGAİN.
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
apparaisse
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
1-PRESS BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
2 Taper 1111 et confirmer à l'aide de la touche
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
3 Taper sur la touche
2-DIAL 1111 AND APPROVE WITH
2.WAY
4 Taper sur la touche
3-DIAL KEY AND COME TO PRO-28 PARAMETER
1-PRESS
5 Taper sur la touche
4-DIAL KEY AND COME TO 1. DIGIT
6 Confirmer à l'aide de la touche
2-DIAL 1111 AND APPROVE WITH
7 Taper de nouveau sur la touche
5-DIAL KEY CHANGE THE WORTH TO ZERO
3-DIAL
8 L'écran sera réinitialisé lorsque vous taperez sur la touche
6-APPROVE WITH
4-DIAL
9 Déplacer l'arc de 60° sur la droite
10 Taper sur la touche
7-DIAL KEY AGAIN AND LEAVE THE PROGRAM PAGE
5-DIAL
11 Déplacer l'arc de -60° en arrière. Bien que l'écran affiche -60°, l'arc est sur 0°
8-SCREEN WILL BE RESET WHEN YOU DEAL
6-APPROVE WITH
12 Appuyer sur la touche
9-MOWE THE BOW 60° RIGHT
13 Vous devez suivre les mêmes étapes et mettre le paramètre p-09 en position 1
7-DIAL
14 Ceci afin que l'opérateur empêche la réinitialisation de la machine lorsque celle-ci est à un angle différent de zéro
10-DIAL KEY AND THE SCREEN WILL BE RESET
8-SCREEN WILL BE RESET WHEN YOU DEAL
Remarque : il est nécessaire de régler les carbures et la lame correctement pour pouvoir lancer le 2nd mode
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
de réinitialisation.
9-MOWE THE BOW 60° RIGHT
Après avoir lancé le 2ème mode, si la lame n'est pas en place, les réglages du carbure peuvent être corrigés
12-DIAL KEY AND RESET
sans modifier l'angle de l'arc.
10-DIAL
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
12-DIAL
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITHOUT CHANGING
LIMIT SWITCHES
THE BOW ANGLE.
LIMIT SWITCHES
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
LIMIT SWITCHES
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITHOUT CHANGING
THE BOW ANGLE.
8
LIMIT SWITCHES
LIMIT SWITCHES
ANGLE ZERO SET
ANGLE ZERO SET
ANGLE ZERO SET
ANGLE ZERO SET
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
1. PRESS "SET" BUTTON İN 10 SECOND.
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
1. PRESS "SET" BUTTON İN 10 SECOND.
2. IT WİLL APPEAR "P00" ON THE DİSPLAY
1. PRESS "SET" BUTTON İN 10 SECOND.
2. IT WİLL APPEAR "P00" ON THE DİSPLAY
3. PRESS "∆" BUTTON UNTİL "P09".
2. 1. IT WİLL APPEAR "P00" ON THE DİSPLAY PRESS "SET" BUTTON İN 10 SECOND.
3. PRESS "∆" BUTTON UNTİL "P09".
4.
ANGLE ZERO SET 2. IT WİLL APPEAR "P00" ON THE DİSPLAY
3. PRESS "∆" BUTTON UNTİL "P09".
4.
5. PARAMETER P09 WİLL BE "YES"
3. PRESS "∆" BUTTON UNTİL "P09".
4.
5. PARAMETER P09 WİLL BE "YES"
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
5. 4. PARAMETER P09 WİLL BE "YES"
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
5. PARAMETER P09 WİLL BE "YES"
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
ANGLE ZERO SET
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
ANGLE ZERO SET
8. 7. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN . WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
10. LOCK THE BOW AGAİN. 1. PRESS "SET" BUTTON İN 10 SECOND.
9. 8. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
10. LOCK THE BOW AGAİN.
2. 11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN . IT WİLL APPEAR "P00" ON THE DİSPLAY
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
10. LOCK THE BOW AGAİN.
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO" 3. PRESS "∆" BUTTON UNTİL "P09".
10. LOCK THE BOW AGAİN.
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU. 4. BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
1. PRESS "SET" BUTTON İN 10 SECOND.
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
5. PARAMETER P09 WİLL BE "YES"
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU. 12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
2. IT WİLL APPEAR "P00" ON THE DİSPLAY
2.WAY
1. PRESS "SET" BUTTON İN 10 SECOND.
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
2.WAY 3. PRESS "∆" BUTTON UNTİL "P09".
2. IT WİLL APPEAR "P00" ON THE DİSPLAY
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
2.WAY
4.
3. PRESS "∆" BUTTON UNTİL "P09".
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
2.WAY
1-PRESS BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
5. PARAMETER P09 WİLL BE "YES"
4.
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
1-PRESS BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
situé sur le compteur emko (ezm-4450) jusqu'àce que l'écran de mot de passe
1-PRESS BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
5. PARAMETER P09 WİLL BE "YES"
10. LOCK THE BOW AGAİN.
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
1-PRESS BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTER WHİCH ONE.
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
2-DIAL 1111 AND APPROVE WITH
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
2-DIAL 1111 AND APPROVE WITH 7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
2-DIAL 1111 AND APPROVE WITH
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
2-DIAL 1111 AND APPROVE WITH
10. LOCK THE BOW AGAİN.
3-DIAL KEY AND COME TO PRO-28 PARAMETER
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
3-DIAL KEY AND COME TO PRO-28 PARAMETER
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
2.WAY
10. LOCK THE BOW AGAİN.
3-DIAL KEY AND COME TO PRO-28 PARAMETER
et aller au paramètre pro-28
KEY
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCREEN .
3-DIAL KEY AND COME TO PRO-28 PARAMETER
4-DIAL KEY AND COME TO 1. DIGIT
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
et aller au chiffre 1.
4-DIAL KEY AND COME TO 1. DIGIT
1-PRESS BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
4-DIAL KEY AND COME TO 1. DIGIT
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
2.WAY
4-DIAL KEY AND COME TO 1. DIGIT
pour que la valeur atteigne zéro
5-DIAL KEY CHANGE THE WORTH TO ZERO
5-DIAL KEY CHANGE THE WORTH TO ZERO
2.WAY
2-DIAL 1111 AND APPROVE WITH 5-DIAL KEY CHANGE THE WORTH TO ZERO
1-PRESS 5-DIAL BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR KEY CHANGE THE WORTH TO ZERO
6-APPROVE WITH KEY
6-APPROVE WITH KEY
1-PRESS
KEY AND COME TO PRO-28 PARAMETER
3-DIAL 6-APPROVE WITH
KEY AND COME TO PRO-28 PARAMETER
2-DIAL 1111 AND APPROVE WITH 6-APPROVE WITH
7-DIAL KEY AGAIN AND LEAVE THE PROGRAM PAGE
7-DIAL KEY AGAIN AND LEAVE THE PROGRAM PAGE
2-DIAL 1111 AND APPROVE WITH
4-DIAL 7-DIAL KEY AND COME TO 1. DIGIT KEY AGAIN AND LEAVE THE PROGRAM PAGE
KEY
KEY AND COME TO 1. DIGIT
3-DIAL KEY AND COME TO PRO-28 PARAMETER
7-DIAL KEY AGAIN AND LEAVE THE PROGRAM PAGE
8-SCREEN WILL BE RESET WHEN YOU DEAL
8-SCREEN WILL BE RESET WHEN YOU DEAL
KEY AND COME TO PRO-28 PARAMETER
3-DIAL
pour que l'écran soit réinitialisé
5-DIAL KEY CHANGE THE WORTH TO ZERO
8-SCREEN WILL BE RESET WHEN YOU DEAL
KEY CHANGE THE WORTH TO ZERO
9-MOWE THE BOW 60° RIGHT
8-SCREEN WILL BE RESET WHEN YOU DEAL
4-DIAL KEY AND COME TO 1. DIGIT
9-MOWE THE BOW 60° RIGHT
9-MOWE THE BOW 60° RIGHT
4-DIAL
6-APPROVE WITH KEY
KEY
9-MOWE THE BOW 60° RIGHT
10-DIAL KEY AND THE SCREEN WILL BE RESET KEY
et réinitialiser
5-DIAL KEY CHANGE THE WORTH TO ZERO
10-DIAL KEY AND THE SCREEN WILL BE RESET
10-DIAL KEY AND THE SCREEN WILL BE RESET
5-DIAL
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
7-DIAL KEY AGAIN AND LEAVE THE PROGRAM PAGE
10-DIAL KEY AND THE SCREEN WILL BE RESET
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION KEY AGAIN AND LEAVE THE PROGRAM PAGE
6-APPROVE WITH
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
12-DIAL KEY AND RESET
6-APPROVE WITH
8-SCREEN WILL BE RESET WHEN YOU DEAL
12-DIAL KEY AND RESET
12-DIAL KEY AND RESET
7-DIAL KEY AGAIN AND LEAVE THE PROGRAM PAGE
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
9-MOWE THE BOW 60° RIGHT
12-DIAL KEY AND RESET
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
7-DIAL
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
8-SCREEN WILL BE RESET WHEN YOU DEAL
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
10-DIAL KEY AND THE SCREEN WILL BE RESET
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO KEY AND THE SCREEN WILL BE RESET
8-SCREEN WILL BE RESET WHEN YOU DEAL
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
9-MOWE THE BOW 60° RIGHT
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
9-MOWE THE BOW 60° RIGHT
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITHOUT
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
10-DIAL KEY AND THE SCREEN WILL BE RESET
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITHOUT
THE BOW ANGLE.
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITH
12-DIAL KEY AND RESET
THE BOW ANGLE.
KEY AND RESET
10-DIAL
THE BOW ANGLE. AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITH
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
THE BOW ANGLE.
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT THE 0° POSITION
12-DIAL KEY AND RESET
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
LIMIT SWITCHES
12-DIAL
LIMIT SWITCHES
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER INTO '1' POSITION.
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITHOUT
THE BOW ANGLE.
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES DIFFERENT THAN ZERO
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW THE 2.WAY FOR RESET.
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORRECTED WITHO
THE BOW ANGLE.
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE ADJUSTMENTS CAN BE CORREC
THE BOW ANGLE.
SOUS TOUTES RÉSER VES DE MODIFICATIONS E T DE FAUTES DE FRAPPE SOUS TOUTES RÉSER VES DE MODIFICATIONS E T DE FAUTES DE FRAPPE
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
4-100.c
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
ANGLE ZERO SET
BEFORE ZERO-SET, THE BOW MUST BE ON UPPER POSİTİON.
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
1. PRESS "SET" BUTTON İN 10 SECOND.
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
2. IT WİLL APPEAR "P00" ON THE DİSPLAY
3. PRESS "∆" BUTTON UNTİL "P09".
4.
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
5. PARAMETER P09 WİLL BE "YES"
6. MOVE THE BODY TİLL YOU SEE +60.0 OR -60.0 DEGREES, DOES NOT MATTE
7. WHEN YOU SEE 60DEGREE THEN LOCK THE BOW.
8. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCRE
9. TURN THE BOW UNTİL TO SEE +60.0 OR -60.0 ON THE DİSPLAY.
10. LOCK THE BOW AGAİN.
11. BY PRESSİNG 'RESET' BUTTON ENABLE '000.0' TO BE WRİTTEN ON THE SCRE
12. KEEP FOLLOWİNG NR.1 TİLL NR.5 TO MAKE P09 "NO"
13. PRESS 'SET' TO GET OUT OF PARAMETERS MENU.
KEY
2.WAY
KEY
KEY
KEY
1-PRESS
2-DIAL 1111 AND APPROVE WITH
KEY AND COME TO PRO-28 PARAMETER
3-DIAL
KEY
KEY
4-DIAL KEY AND COME TO 1. DIGIT
et quitter la page de programme
BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWORD SCREEN APPEAR
KEY
KEY KEY
5-DIAL KEY CHANGE THE WORTH TO ZERO
KEY
KEY
6-APPROVE WITH
KEY
KEY
KEY
7-DIAL KEY AGAIN AND LEAVE THE PROGRAM PAGE
KEY AND COME TO 1. DIGIT
8-SCREEN WILL BE RESET WHEN YOU DEAL
KEY CHANGE THE WORTH TO ZERO
9-MOWE THE BOW 60° RIGHT
KEY
KEY
KEY
KEY
10-DIAL KEY AND THE SCREEN WILL BE RESET
KEY AGAIN AND LEAVE THE PROGRAM PAGE
11-MOWE THE BOW -60° BACK.DESPITE THE SCREEN BE SEEN AS -60°,THE BOW IS AT
KEY
12-DIAL KEY AND RESET
13- YOU MUST FOLLOW THE SAME OPERATION STEPS AND PUT THE P-09 PARAMETER
14- SO OPERATOR PREVENT THE MACHINE RESET WHEN THE MACHINE IS AT ANGLES
KEY AND THE SCREEN WILL BE RESET
NOTE:ITS IS NECESSARY TO ADJUST THE CARBIDES AND BLADE CORRECT TO FOLLOW
AFTER APPLYING THE SECOND WAY IF THE BLADE IS NOT AT SET SQURE ,CARBIDE A
KEY AND RESET
THE BOW ANGLE.
LIMIT SWITCHES
ZERO SET FOR TCS4-100.C DISPLAY DEVICE
BUTTON ON THE EMKO COUNTER (EZM-4450) UNTIL SEE PASSWO
KEY
KEY
KEY
ZERO SET FOR TCS4-100.C DISPLA
KEY