Hozelock PortaShower Mode D'emploi page 4

21
GB
Thank you for choosing a Hozelock quality sprayer, you can be
assured of many years of reliable service from this product.
Instructions & Warnings
• Before carrying out any maintenance on this sprayer, it
is essential to depressurise the bottle by activating the
pressure release valve.
Do not spray any solvent e.g. White spirit.
Do not over pressurise the bottle, or tamper with the
pressure release valve. The pressure release valve is
designed to release excess pressure do not interfere with it
or force it to remain closed.
Winter Use – drain liquid from all parts and prevent
damage from freezing.
Annual maintenance – At least once per year thoroughly
clean the whole sprayer and apply silicone grease to all
moving parts & seals. Test with water, and if any washer or
seal has perished it must be replaced.
Ensure the hose fully covers the barbed details on both
A
the lance, and the outlet connection. Make sure all nuts
are hand tight before use.
This sprayer is made from many types of plastic, and
B
although the liquid you wish to spray may also be packed
in plastic, this does not guarantee it will not damage
the sprayer. If you have any doubt about compatibility,
contact Hozelock consumer services. When filling
the sprayer ensure that the maximum fill level is not
exceeded.
C
Ensure that the pump is screwed into the bottle tightly
and locked in position.
Before operating the pump, operate the pressure
D
release valve manually by lifting the knob to ensure
it is free to move, then release the handle by rotating
anticlockwise, pressurise bottle and then lock back in
position.
After using the sprayer, manually operate the pressure
E
release valve as above, to depressurize.
If the sprayer has been used with chemicals discard any
F
unused solution in an environmentally friendly manner.
Fill sprayer with warm water (not hot), re-assemble the
G
sprayer and spray some of the contents. Repeat; check
that the nozzle is free from sediment. If necessary repeat
the process until the sprayer is clean. NB : Do not use
detergent.
A
Notes
22
I
The pump assembly and pressure release valve o rings
H
should be lubricated to allow the sprayer to pump air
efficiently. Access the seals by unscrewing the plunger
retaining ring. Apply silicone grease regularly to the pump,
piston and release valve o ring seals (A).
Keep the trigger clean and free from build up of sediment
I
and chemicals by regularly flushing after use. If necessary
remove and clean the shuttle in the trigger.
To clean or replace the outlet o ring seal, unscrew the
J
retaining nut (B), and pull out the spigot (C).
• Hozelock guarantees this sprayer against any defect arising
from faulty materials or workmanship for a period of 1 year
from the date of purchase, provided that it has only been
used in accordance with these instructions. The guarantee
is limited to the repair or replacement of any defective or
faulty item. Proof of purchase must be retained.
• The Hozelock guarantee also covers 'O' rings and seals for
a 12-month period, as these are wearing parts, they are
available as spares from the retailer or from Hozelock direct.
Troubleshooting
Issue Problem
Weak or Sprayer
no spray will not
pressurise
Loss of
pressure
Obstruction
Leaks Build up of
sediment
or foreign
matter on
sealing
surfaces
Worn or
damaged
'O' rings or
washers.
B
C
Guarantee
Solution
Ensure all connections are tight
Check 'O'-rings and seals are
lubricated and show no signs
of wear or damage – replace if
required
(see notes H, I and J)
There could be a blockage in
the nozzle, the trigger or the
outlet hose
Check 'O'-rings and seals are
free from dirt – Clean or replace
if required
Check 'O'-rings and seals are
free from wear or damage –
replace if required
J