Basic Remote Control Operations For Other Components; Registering Setup Codes For Other Components; Searching For Your Codes; Checking The Codes - Kenwood KRF-X9070D Manuel D'instructions

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Basic remote control operations for other components

The remote control supplied with this receiver is also capable
of controlling components from a variety of manufacturers
once you register the appropriate setup codes into the
remote control unit.
Low battery warning
Replace all two batteries with new ones when you notice a shortening
of the distance from which the remote control will operate.The
remote control is designed to retain setup codes in memory while
you change batteries.
• To initialize the remote control, press the Learn key until
twice. Then press the numeric key to enter "9-8-1".
twice.

Registering setup codes for other components

SRC Power
1
Find the setup code of the component to be registered.
• Refer to the setup code lists to find the setup code for the
component to be registered.
Example: To register a DVD made by KENWOOD, you would enter
"0534".
Input
Component
(DVD)
DVD player
KENWOOD
Source key
TUNER
DVD/6CH
CD/DVD
MD/TAPE
VID1 , AV AUX
VID2
VID3
PHONO
TV
2
Press the Source keys (DVD/6CH, CD/DVD, VID1, VID2, VID3,
TV, MD/TAPE, AV AUX, PHONO).
• PHONO key has to re-assigned to another key before a setup
code can be registered.
• While in Tuner mode, setup code function will not be available.
3
Press and hold the Learn key until the
release the Learn key.
will blink
Source
keys
Numeric keys
Learn
Maker
Code
Key
0534
DVD/6CH
Other components
Receiver (Kenwood)
DVD
CD and MD (Kenwood)
Cassette deck (Kenwood)
VCR and PVR
Cable and DTV decoder
Satellite
Additional key for re-assigning
TV/VCR combo, TV/DVD combo, TV
blinks twice, then
4
Press the Numeric keys to enter the four-digit code for the
component to be registered.
• If performed correctly,
• Point the remote control at the component and press SRC Power
key once. It should turn on/off but if it does not, repeat step 2 to 4
• If the component still does not work, try searching for the code.
5
Repeat steps 2 to 4 to register additional components until
all components have been registered.
blinks
Note
Although each setup code is designed to work with a number of
different models, certain codes may not work with some models.
(Also, certain codes may only operate some of the functions available
on a given model.)

Searching for your codes

If your component does not respond after trying all the codes listed for
your component, or if your component is not listed at all, try searching
for your code.
For example, to search for code for your TV:
1
Press the TV key once. Next, press and hold the Learn key
until
blinks twice, then release the Learn key.
2
Press the numeric key to enter "9 - 9 - 1".
will blink twice.
3
Point the remote control at the TV and slowly alternate
between pressing the TV Power and TV key.
Stop when the TV turns on/off.
w
In the search mode, the remote control will send IR codes from its
library to the selected device, starting with the most popular code
first.
4
Press the Learn key once to lock in the code.
5
To search for the codes of your other components, repeat
steps 1 through 4 , but substitute the appropriate key (i.e.,
DVD/6CH, CD/DVD, VID1, VID2, VID3, TV, MD/TAPE, AV AUX,
PHONO, SRC Power).
PHONO key has to be re-assigned to another key before a setup
code can be programmed.

Checking the codes

If you have setup the remote control using the procedures described in
"Searching for your codes", you may need to find out which four-digit
code is operating your equipment:
For example, to find out which code is operating your TV:
1
Press the TV key once. Next, press and hold the Learn key
until
blinks twice, then release the Learn key.
2
Press the numeric key to enter "9 - 9 - 0".
will blink twice.
w
3
To view the code for the first digit, press "1" once. Wait for 3
seconds, counts the number of times
and write down that number.
If a code digit is "0", the
will blink twice.
blinks (e.g., blinks=3)
will not blink.
Continued to
39
EN

Publicité

Table des Matières
loading

Table des Matières