Kenwood KRF-X9070D Manuel D'instructions page 23

Preparing for surround sound
6
Adjust the bass peak level.
A restriction is put on the low frequency so that the bass peak level
will not go higher than the acceptable level when the volume is
increased.
If subwoofer speaker is OFF, the limitation will affect the low
frequency of the front left and right speakers
1 Press the ∧ ∧ ∧ ∧ ∧ / ∨ ∨ ∨ ∨ ∨ keys or @ / # keys to select BASS PEAK and press
the SETUP key.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG
SW
LFE
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the bass peak level to –30dB.
• The adjustment range is from – 30dB to 0dB and OFF.
3 For optimum bass peak level, keep increasing the bass peak
level by using the MULTI CONTROL knob or Multi (%/fi)keys
while test tone is being output until clip sound is heard from
the subwoofer or front speaker.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG
SW
LFE
4 Press the SETUP key to accept the setting.
7
Input the distance to the speakers.
1 Press the keys or @/# keys to select the SP DISTANCE
∧ ∧ ∧ ∧ ∧ /∨ ∨ ∨ ∨ ∨
on setup displays and press the SETUP key again.
2 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front left speaker (L)
Distance to Center speaker (C)
Distance to Front right speaker (R) : ____ feet (meters)
Distance to Surround right (SR)
Distance to Surround back (SBR)
Distance to Surround back (SBL)
Distance to Surround left (SL)
Distance to Subwoofer (SW)
3 Use the keys or @/# keys to select the speakers and the
∧ ∧ ∧ ∧ ∧ /∨ ∨ ∨ ∨ ∨
MULTI CONTROL knob or Multi (%/fi) keys to adjust the
distance to the front speakers.
The speaker indicator to be adjusted blinks.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG
L
SL S SB SR
Indication in feet
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),
adjustable in 1 foot (0.3 m) increments.
4 Repeat steps 3 to input the distance for each of the speakers.
5 Press the SETUP key again to return to main setup displays.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
THX
ACTIVE EQ. MATRIX
Surround EX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
THX
ACTIVE EQ. MATRIX
Surround EX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
THX
ACTIVE EQ. MATRIX
Surround EX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
Indication in meters
8
Select the display mode.
1 Press the ∧ ∧ ∧ ∧ ∧ /∨ ∨ ∨ ∨ ∨
2 Press the SETUP key for the following displays:
1 DISP SELECTOR
2 DISP LISTEN
3 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the display mode.
RDS
SP MUTE
RTY
A B
L C SW R
AUTO
LFE
MEMO
STEREO
TUNED
SL S SB SR
4 Press the SETUP key again to accept the setting.
5 Use the key or # key to select EXIT.
∧ ∧ ∧ ∧ ∧
SP
A B
L C SW R
LFE
SL S SB SR
6 Press the SETUP key to exit the SETUP mode.
RDS
RTY
AUTO
MEMO
Input level adjustment (analog sources only)
STEREO
TUNED
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
1 Use the Input Selector keys to select the source of which the
input level you want to adjust.
• You can store a separate input level for each input source.
2 Press the SOUND and
the "INPUT" indication appears.
3 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust the
input level.
SP MUTE
A B
L C SW R
LFE
SL S SB SR
• The adjustment mode is displayed for approximately 8 seconds.
• The input level may be adjusted to any one of three settings:
0dB, -3dB, and -6dB. (The initial setting is 0dB.)
RDS
RTY
AUTO
4 Press the SOUND key again to return to the input indication.
MEMO
STEREO
TUNED
keys or @/# keys to select the DISP MODE.
: Displays the current input selector.
: Displays the current listen mode.
OPTICAL 6CH INPUT CINEMA EQ. DTS. DOLBY DIGITAL
AUTO DETECT
ACTIVE EQ. MATRIX
CLIP
COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC
MUTE OPTICAL 6CH INPUT CINEMA EQ. DTS. DOLBY DIGITAL
AUTO DETECT
ACTIVE EQ. MATRIX
CLIP
COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC
SP MUTE OPTICAL 6CH INPUT
AUTO D
A B CLIP CLIP CLIP
COAXIAL ANALOG 96k
L C SW R
LFE
SL S SB SR
keys or @/# keys repeatedly until
∧ ∧ ∧ ∧ ∧ /∨ ∨ ∨ ∨ ∨
OPTICAL 6CH INPUT CINEMA EQ. DTS. DOLBY DIGITAL
AUTO DETECT
ACTIVE EQ. MATRIX
CLIP
COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC
STEREO NEO:6 RDS
THX
RTY
Surround EX
LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
STEREO NEO:6 RDS
THX
RTY
Surround EX
LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
STEREO NEO:6 RDS
THX
RTY
Surround EX
LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
23
EN