Advanced Programming; Programming Parameters - Aprimatic RSK24 SMT Notice D'installation

Advanced programming

4. ADVANCED PROGRAMMING
4.1

PROGRAMMING PARAMETERS

IMPORTANT! Before you start programming parameters, make sure that the gate is CLOSED and STOPPED and
that the SELF-TEACH procedure has been completed.
To program the parameters, follow the instructions given in Fig. 7 and Tab. 2 below.
!
Warning
All input signals will be ignored during programming.
Press and hold down the RED button until the letter P appears on the display. Release the button
a programmable parameter will appear on the display.
To scroll through the parameters, press the BLUE button.
To leave the programming mode and return to normal operation, press the YELLOW button.
To display the current parameter value (shown by a bright dot), press the RED button;
available, press the BLUE button.
To modify a value, press the RED (Confi rm) button for 3 seconds when the value required is displayed
is displayed (confi rmed by 3 fl ashes) and the system leaves the programming mode and returns to normal operation.
If you decide not to modify a value, press the YELLOW button.
the parameter.
Note: The OPERATING MODES and the signal responses are described in sect. 5.1.
Fig. 7
Red to enter
programming
mode
Tab. 2
: wing closing delay
0 = 4 seconds (*)
Note: the delay
1 = 8 seconds
time on opening
2 = 12 seconds
is fi xed at 3
3 = 16 seconds
seconds.
: short inversion (ms.)
0 0
1 30
2 (*) 50
3 80
4 100
5 120
6 150
7 200
8 300
9 400
: approach time (sec.)
0 = 2
1 = 4
2 = 5
3 = 6
4 = 7 (*)
5 = 8
6 = 10
7 = 12
8 = 14
9 = 16
IMPORTANT NOTE:
Blue
To select
Release
Blue
to select parameter
to be modifi ed
: thrust force
0 = Low
1 = Medium
2 = High (*)
3 = Very high
4 = Medium wind
5 = Strongly wind
: prefl ashing
0 (*) no
1 no
2 yes
3 yes
: Pause time
photocell
0 (*) NO
1 YES
2 NO
3 YES
Yellow
Red
To confi rm To exit
The display will return to showing the initial letter of
Red
to confi rm
parameter
CAUTION: any increase
in this parameter causes
a reduction in obstacle
recognition sensitivity. If a
value of 3, 4, or 5 is set, use
special detection devices
on the basis of correct risk
assessment.
reverse stroke
no
yes
no
yes
Input function
J1 pin 6-9
OPENING SAFETY SAFETY EDGE
OPENING SAFETY SAFETY EDGE
OPENING SAFETY PHOTOCELL
OPENING SAFETY PHOTOCELL
- 20 -
the initial letter of
to scroll through the values
Blue
Red
to select to confi rm
new value new value
: Operating mode
0 = AUTOMATIC (*)
1 = 4 STEPS
2 = SUPER AUTOMATIC
3 = SEMIAUTOMATIC with STOP
4 = STEP-BY-STEP
: wing travel speed
0 = 50%
1 = 70%
2 = 85% (*)
3 = 100%
CAUTION When the S (speed)
parameter is changed, you must
perform the self-teach procedure again.
To do this, press and hold down the
YELLOW and BLUE buttons together
for a few seconds (see section 3.1).
: pause time (sec.)
0 = 0
1 = 5 (*)
2 = 10
3 = 15
4 = 20
5 = 25
6 = 30
7 = 35
8 = 40
9 = 45
( * ) = default values
the new value