Carrera DIGITAL 124 Instructions De Montage Et D'utilisation page 11

pushed, switch on Control Unit and release "SPEED" button
By pushing the button again, 1 or 2 LEDs will light depending on
the setting.
• LED 1 = lap counting function deactivated
• LED 1 + 2 = lap counting function activated
Select the desired setting and push or drive a car across the Pit
Lane Sensor, fi g. . The settings will now be adopted. Push
5
4
"START/ENTER" 3 for leaving the settings again.
Sound ON/OFF
5
1
2 1
4
3
7 8
5
2 1
The confi rmation sound when crossing the sensors and the key
sound can be switched off . Switch off the Control Unit and keep the
7 8
"START/ENTER" button 3 pushed, switch on the racetrack and
3
release "START/ENTER" again. The acknowledgement sound
for switching on the Control Unit cannot be switched off however.
Reset function
1
2 1
3
7 8
2 1
To restore the Control Unit to factory settings the Control Unit off ers
a reset function.
7 8
Switch off the Control Unit and keep the "ESC/PACE CAR"
ton pushed; switch on the ractrack and release the button again. All
previous settings for speed, braking performance, tank fuel capac-
ity, sound and lap counting will be restored to factory settings. The
cars´ settings will remain unaff ected by this measure unless they are
placed on the racetrack.
Factory settings:
• speed = 10
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
Energy-saving mode
After 20 minutes of non-usage the Control Unit switches to ener-
gy-saving mode and all displays such as Position Tower, Driver
Displays and Startlight are turned off . To reactivate the controller,
switch it off for 2 or 3 seconds, then switch it on again. All settings
will be kept.
5 .
1
3 2
Driving without starting sequence:
Driving without starting sequence:
6 7
1. Switch on the Control Unit (ON-OFF)
2. After approx 1 second the central LED lights permanently and a
brief acoustic signal will sound , fi g
2
3. Place the car/s on the connecting track
4. In this mode the track is cleared without starting light signal; you
can start immediately.
3 2
3
6 7
4
5
5
Driving with starting sequence:
With the starting sequence being initiated all displays will be reset.
1. Switch on the Control Unit (ON-OFF)
2. After approx 1 second the central LED lights permanently and a
brief acoustic signal will sound , fi g.
2
3. Then push start button until all LEDs will light, fi g.
4. Place the car/s on the connecting track, fi g.
5. Push start button again - the starting sequence is initiated, the
LEDs are lit and acoustic signals can be heard.
6. With elapse of the starting light procedure (LEDs light individu-
4 3
ally) the race is released, fi g.
7. False start: If a car´s speed controller is actuated during the
starting light phase, this is rated as false start. The vehicle having
caused the false start will travel a short distance and the LED on
5 6
the relevant car or speed controller will fl ash. The race will not be
released and the start has to be repeated.
4 but-
1
To ensure a proper operation of the motor-racing circuit, all race-
track components should be regularly cleaned. Pull the plug prior
to cleaning.
Racetrack: Keep the track surface and track slots clean with a
1
dry cloth. Do not use any solvents or chemicals for cleaning. When
it is not in use, store the racetrack in a clean and dust-protected
location, preferably in the original cardboard box.
Troubleshooting:
In case of any malfunctions, please check the following:
• Has the connection to the power supply been established correctly?
• Have transformer and speed controllers been connected
correctly?
• Are the track connections faultless?
• Are the racetrack and track slots clean and free of any foreign
objects?
• Are the sliding contacts in order and do they make contact with
the track slot?
• Are the cars correctly coded to the according speed controller?
• The track's current feed will be switched off automatically for 5
seconds, if there is an electrical short circuit: this will be notifi ed by
audible and visual signals.
Starting sequence
2
1
8
2
1
4
8
3 2
6
6 7
.
2
.
4
.
5
2 1
6 .
7 8
Maintenance and care
Troubleshooting
Driving tips
• Are the cars placed on the track in running direction? In case of
non-functioning push the running direction switch which is on the
car´s bottom.
Note:
During operation small car parts as spoilers or mirrors may get off or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.
Driving technique:
• You can drive fast along the straight track but you should brake before
the curve and then accelerate again when coming out of the curve.
• Do not fasten or block the vehicles when the motor is running:
overheating or damage to the motor could result otherwise.
Note: When using track systems which are not manufactured by
Carrera the existing guide keel has to be replaced by the spe-
cial guide keel (#20085309). While using the Carrera crossing
(#20020587) or high banked curve 1/30° (#20020574) slight driving
noise might occur which is due to the full-scale genuineness and
does not aff ect fl awless operation.
All Carrera spare parts are available in the webshop:
carrera-toys.com
Technical specifications
1
Output voltage: Toy transformer
8
18 V 54 VA (Carrera DIGITAL 124)
14,8 V 51,8 VA (Carrera DIGITAL 132)
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode.
The LED is no longer lit.
CURRENT CONSUMPTION < 0,5 watt / 0,5w
To reactivate the controller, switch it off for 2 or 3 seconds, then
switch it on again. The racetrack is then once again in standby mode.
4.) Off -state = power supply unit disconnected from mains supply
This device is marked by "selective sort throught" symbol related to
sort through domestic, electric and electronic, waste. This means
the product must be treated by a specialized "sorting/collecting" sys-
tem in accordance with European directive 2012/19/EU, to reduce
the impact upon environment. For more precise information, please
contact your local administration. Electronical product which are
not going through special collecting, are potentially dangerous for
environment and human health, because of dangerous substance.
Output voltage: Toy transformer
18 V 54 VA (Carrera DIGITAL 124)
14,8 V 42,9 VA (Carrera DIGITAL 132)
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode.
The LED is no longer lit.
CURRENT CONSUMPTION < 0,5 watt / 0,5w
To reactivate the controller, switch it off for 2 or 3 seconds, then
switch it on again. The racetrack is then once again in standby mode.
4.) Off -state = power supply unit disconnected from mains supply
Conforms to the safety requirements of ASTM F963.
11