Technical Data; Maintenance And Cleaning - TOOLCRAFT 19 27 29 Mode D'emploi

c) Switching the product off
Do not leave the product to cool down unattended. There is a risk of fire.
• After use, place the woodburning pen on the safety support.
• Disconnect the mains plug from the wall socket.
• Let the product cool down completely before you put it in storage.
General notes
Do not apply the woodburning pen on materials with a lacquered surface.
Ensure the workpiece is clean, flat and free from grease.
Always work in well-ventilated areas, as the fumes can irritate or even damage eyes and/or
the respiratory system.
• When decorating, try to apply even pressure and speed of movement to achieve uniformly dark lines.
• Be careful not to destroy the workpiece when working on sensitive materials such as thin leather.
• With every new material, first practise on a sample piece.
• The longer a burning stamp is applied, the darker the motif becomes.
• For soldering works, a solder and flux are required. Many solders already contain flux. For cleaning the
soldering tip, a wet soldering sponge is also required. Accessories for soldering work are not included in
delivery.
Pyrography
• Select one of the burning tips as a tool.
• Clean the workpiece, if required. Use fine sandpaper to sand down the surface.
• The motif can be sketched out with pencil or carbon paper on the material.
• You can also print out motifs on special ironing paper and apply onto the material.
• Turn the product on.
• Only hold the product on the handle, do not touch the metal part.
• Hold the product as you would a fountain pen.
• Guide the burning tip across the workpiece, applying light pressure.
• Decorate wood, cork or leather, for example.
Burning stamps
• Select one of the burning stamps as a tool.
• Turn the product on.
• Hold the product by the handle, perpendicular to the workpiece.
• Put the stamp on the workpiece, applying light pressure.
• Decorate wood, cork, leather or sealing wax, for example.
Heat cutter
• Select the blade and the blade holder as tools.
• Insert the blade into one of the slots on the blade holder.
• Screw the blade holder onto the product.
• Turn the product on.
• Only hold the product on the handle, do not touch the metal part.
• Cut polystyrene, for example, with the heat cutter.
Soldering iron
• Screw the soldering tip onto the product.
• Turn the product on.
• Clean the soldering joints of grease, dirt, as well as from oxides and sulphides.
• Only hold the product on the handle, do not touch the metal part.
• Using the soldering tip, lightly apply solder onto the solder joints and solder them together.
• If required, apply flux.
• Ensure the soldering tip only touches the soldering joints.
• Clean the soldering tip with the soldering sponge.

Maintenance and cleaning

• The woodburning pen requires no servicing aside from occasional cleaning.
• Disconnect the mains plug from the wall socket.
• Let the woodburning pen cool down to room temperature before cleaning.
• Use a soft, anti-static and lint-free cloth for cleaning.
• Do not use any chemical or abrasive cleaning agents.
• For cleaning the tools, screw them onto the product and start up the product.
• Clean the hot tool using a damp, inflammable sponge.
• Do not clean the tools with metal brushes or sandpaper.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

Operating voltage .................................................................. 2 30 V/AC, 50 Hz
Output power . ........................................................................ 3 0 W
Temperature range (Burning tips, Burning stamps) . .............. 5 00 – 580 °C
Temperature range (Heat cutter) ........................................... 2 20 – 280 °C
Temperature range (Soldering iron) . ...................................... 4 70 – 530 °C
Cable length .......................................................................... 1 .5 m
Dimensions (L x Ø) . ............................................................... 1 72 x 29 mm (Woodburning pen)
Weight ................................................................................... a pprox. 170 g (Woodburning pen)
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE. V1_0313_02-ETS-JL