Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
SYSTEM LAY-OUT
Fig. 2
Parts to install meeting the EN 12453 standard
COMMAND TYPE
with manned operation
with visible impulses (e.g. sensor)
with not visible impulses
(e.g. remote control device)
automatic
* a typical example are those shutters which do not have access to any public way
A: Command button with manned operation (that is, operating as long as activated), like code ACG2020
B: Key selector with manned operation, like code ACG1010
C: Safety edges, like code ACG3010
D: Photocells, like code ACG8026
Fig. 3
Fig. 4
USE OF THE SHUTTER
Skilled persons
Skilled persons Unrestricted use
(out of a public area*)
(public area)
A
B
C
C
C
C e D
C e D
C e D
MAGIC operator
Tuned aerial
Flashing lamp
Photoelectric cells (external)
Photoelectric cells (internal)
Key selector
PRE-INSTALLATION CHECKS
The leaf must be fixed firmily on the hinges to the pillars, must not be flexible during the
movement and must move without frictions.
Before the installation of MAGIC, verify all dimensions etc.
There's no need for any modification, if the gate is like that shown in Fig. 2.
N.B.: Gate features must be uniformed with the standards and laws in force. The
door/gate can be automated only if it is in a good condition and its conditions comply with
the EN 12604 norm.
- The door/gate leaf does not have to have a pedestrian opening. In the opposite case it
is necessary to take the appropriate steps, in accordance with EN 12453 norm (for
instance; by preventing the operation of the motor when the pedestrian opening is
opened, by installing a safety microswitch connected with the control panel).
TECHNICAL
DATA
Max. leaf length
Max. leaf weight
Average opening time
Max torque
Power supply
Motor capacity
C e D
Power absorbed
C e D
C e D
Capacitor
No. cycles
Power supply
Motor capacity
Power absorbed
Capacitor
No. cycles
Lubrification
Weight of electroreducer
Noise
Volume
Protection
GEARMOTOR TECHNICAL CHARACTERISTICS
The MAGIC is a reversible operator with a mechanical cluth to adjust the force of the
motor ad its reversibility (more force you set, less reversible it is).
The operator comes complete with a mechanical limit switch group, a transmission lever,
and a trafficable cover.
The MAGIC is supplied as a compact unit complete with a steel foundation box
(41x25x17h cm).
The profile of the box is recessed to facilitate installation.
The MAGIC functions as a load-bearing centre hinge, designed in such a way that the
motor can be removed for servicing purposes without taking down the gate.
The MAGIC drive is reversible, and therefore requires no release mechanism.
The MAGIC will comfortably operate gates and doors up to 350 kg in weight and 2.5
metres in length, with an opening time of 20 seconds for the 105° version and 40
seconds for the 180° version (in compliance with current standards).
MAGIC 105° version (fig 3): this has a system controlling the speed of the opening and
closing movements (opening movement initially slow, then fast; closing movement
initially fast, then slow immediately before shutting).
MAGIC 180° version (fig 4): installing this version, a gate can be rotated through 180° if
the drive shaft is coaxially aligned with the hinge centre, or through 150° with the drive
shaft offset from the centre of rotation by up to 4.5 cm.
Pag. 15 di 32
MAGIC
105°
180°
mt
2,5
Kg
350
sec.
20
40
Nm
250
230V~ 50/60Hz
W
190
A
0,8
F
6,3
n°
40 - 20s/2s
120V~ 60Hz
W
200
A
1,8
F
25
n°
19 - 20s/2s
Bechem Staroel NR100
Kg
21
db
<70
m
3
0,020
IP
677
E
N
G
L
I
S
H
Publicité
Table des Matières
