Starting And Stopping The Machine; Standard Equipment - Virutex FRE317S Mode D'emploi

wire may make exposed metal parts of the power tool
"live" and shock the operator.
-Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it
unstable and may lead to loss of control.
2. SPECIFICATIONS
Universal motor........................................................50/60 Hz
Input power...................................................................1,800W
No-load speed........................................11,500-23,000/min
Chuck collet Ø................................................................12 mm
Maximum bit diameter...............................................61 mm
Routing depth...........................................................0-100 mm
Revolving depth gauge..........6-position depth adjustment
Weight..................................................................................5.5 Kg
Weighted equivalent continuous
acoustic pressure level A..............................................91 dBA
Acoustic power level A.............................................102 dBA
Uncertainty...............................................................K = 3 dbA
Wear ear protection!
Vibration total values.......................................a
Uncertainty.........................................................K: 1.5 m/s

3. STANDARD EQUIPMENT

The box contains the following items:
- FRE317S Angle trimmer
- Angle bit R. 10 mm d.12 HM ref. 1740324
- Groove bit D. 10 mm d. 12 HM ref. 1140257
- Lateral fence assembly ref. 1745745
- Reducer 12 to 10 mm ref. 6022391
- Reducer 12 to 8 mm ref. 6022387
- Reducer 12 to 6 mm ref. 6022388
- Template guide Ø ext. 30 mm ref. 7722114
- Allen key 3 mm a/f
- Allen key 5 mm a/f
- Spanner 13 mm a/f
- Spanner 24 mm a/f
- Bar wrench ref. 6027022
- Dust collector cover to trim radius 1723615
- Dust collector pipe with connectors, length 5 m
- Holding brackets for dust collector pipe
- Guard for planer trimmer ref. 1702744
- Operating instructions and other documentation
4. APPLICATIONS OF THE MACHINE
The high power 1,800 W angle trimmer is ideal for
working with mineral materials like Corian, Rausolid,
etc., with good results being guaranteed.
Its special design allows for two different uses of the
machine:
With its motor in an upright position, it is a standard
10
router, with a long working run, ideal for making and
repairing elements made of mineral materials. Placing
the motor at 45º allows it to work as a single trimmer
for angle trimming the rims of worktop joints or even
vertical corners and joints between two rims.
The machine is equipped with a dust collector connec-
tion, and the dust collector attachment allows it to be
connected to our AS182K, AS282K, AS382L or ASC482U
or to any other industrial dust collector.
5. OPERATIONS COMMON TO BOTH USES
The following operations and settings are for milling rim
joints, and using the machine as a router:

5.1. Starting and stopping the machine

The switch box A has a trigger, B, which starts the
machine, and a safety button C (Fig. 1 and 4). Start the
machine by pressing the safety button C, and, without
releasing it, squeezing the trigger B to start the machine.
If trigger B is pressed again, the safety switch automa-
tically trips and the machine stops. The safety switch
prevents the machine from starting accidentally.
: <2.5 m/s
2
h
2
5.2. Speed control: 11,500 – 23,000 rpm
The electronic speed control adjusts the speed of the
motor to suit the size of the cut and the hardness of
the material used for a better finish and to increase
machine performance.
The electronic speed control of the FRE317S, ensures
constant speed even when under load. Increase or reduce
the speed of the machine by turning the control button
to the right or left as required. There are 6 reference
numbers to simplify finding the correct speed.
The table below shows the position of the electronic
speed control.
The same table is also on the machine itself.
1
2
3
Always make sure that the trimmer is not
in contact with the working part before
starting the machine. Once the machine
has reached its maximum speed, make
contact with the working part and only
stop the machine once the bit is fully clear.
This will increase the quality of the work.
R.P .M
11,500 4
13,800 5
16,100 max.
Adjust the speed in accordance with, the
recommendations of the cutting tool
manufacturer.
18,400
20,700
23,000