Table des Matières
Publicité
Liens rapides
Publicité
Table des Matières
Manuels Connexes pour Paslode IMPULSE IMLi200
Sommaire des Matières pour Paslode IMPULSE IMLi200
- Page 1 Impulse Part No. 903700 IMLi200 Brad Nailer IMPORANT! OPERATING MANUAL DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A. © 2015 Illinois Tool Works Inc. 903720-1 04/15...
-
Page 3: Table Des Matières
Contents Introduction and Warranty..........2 An Overview of Paslode Impulse™ 18 Gauge Brad Nailer ..................3 Safety Instructions ............4 Battery and Charger ............7 Fuel Cell and Metering Valve .......... 9 Preparing the Paslode Impulse 18 Gauge Brad Nailer for Use ................12 Paslode Impulse 18 Gauge Brad Nailer Operation .. -
Page 4: Introduction And Warranty
WARRANTY STATEMENT parts and accessories will be free from defects in material and Paslode's sole liability hereunder will be to replace any part or accessory workmanship for the period shown below, after the date of which proves to be defective within the specific time period. Any replacement delivery to the original user. - Page 5 An Overview of the Paslode Impulse™ 18 ga. Brad Nailer Specifications Description Dimensions: Weight- 4 lbs 14oz. with battery The Paslode Impulse 18 ga. Brad Nailer is a self-contained, Height 11-1/2 inches fully portable nailer that uses liquid hydrocarbon fuel to...
-
Page 6: Safety Instructions
The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Paslode Impulse™ 18 ga. Brad Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY Do not expose the tool to PRECAUTIONS AND MANUAL INSTRUCTIONS. - Page 7 EAR safety gear when until it is completely against the work surface. working with or in the NEVER operate the tool if the work contacting element vicinity of the Paslode is not working properly. Impulse™ 18 ga. Brad Nailer. 8. ALWAYS...
- Page 8 Battery Disposal: The Paslode lithium-ion batteries contain lithium and must be recycled or disposed of properly. It is illegal in some areas to place a lithium-ion battery into the trash or solid waste stream. You may contact your local recycling information on where to return the spent battery or call 877-646-4025 for information on lithium-ion battery recycling in your area.
- Page 9 This charging system is stable surface. A green light will come on to indicate the only one that will work with the Paslode the power is on and the charger circuit is ready. lithium-ion batteries. The first step in preparing a new tool for operation is to fully charge the battery.
-
Page 10: Battery And Charging System
Battery and Charging System Battery Indicator Light On the right side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. If the indicator light blinks red, recharge the battery. -
Page 11: Fuel Cell And Metering Valve
Never inhale the spray. NOTE: Altitude Restriction Keep out of the reach of children. Paslode Impulse technology is powered by an Store fuel cell(s) in well-ventilated areas only. internal combustion engine and are effected by altitude. The tool may lose power or not cycle... - Page 12 3. The valve is now completely seated onto the fuel can and can be inserted into the tool. NOTE: Paslode Impulse™ fuel cells are marked with an expiration date on the bottom of the can. For maximum performance use fuel before expiration date.
- Page 13 Fuel Cell and Metering Valve Inserting Fuel Cell As you slide the metering valve/fuel cell assembly into the Impulse Brad Nailer, you will notice a yellow adapter at the Inserting the metering valve/fuel cell assembly into the top of the cylinder pocket. As shown in the illustration, this Impulse Brad Nailer is very simple.
-
Page 14: Loading Fasteners
18 gauge fasteners designed to be used with the tool. Use the Impulse Brad Nailer outdoors, in dry weather, The use of fasteners that do not meet Paslode standards when the nailer, fuel cell, and battery are between could cause tool damage and will void all warranty 20°F (-7°C) and 120°F (49°C). -
Page 15: Paslode Impulse 18 Gauge Brad Nailer Operation
Paslode Impulse™ 18 ga. Brad Nailer Operation Operation: PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion chamber and Turn mixed with air by adjustment the fan. wheel in either direction SQUEEZE... -
Page 16: Fasteners And Applications
Paslode 18 Gauge Brad Nails. Fasteners are collated into strips of 50 for easy loading. Paslode fasteners are designed to be used in Paslode tools, use of other fasteners may cause damage to the tool or injury to the tool operator. -
Page 17: Servicing
Nailer, clearing a jammed fastener is easy: DANGER 1. Remove the battery. Never attempt any maintenance of a Paslode Cordless 2. Pull the latch, releasing front guide. Pivot front guide tool without first removing the fuel cell and battery. forward. -
Page 18: Air Filter
4. Check work contacting element to ensure it is operating freely. GRILLE Paslode Impulse Tool Accessories A variety of accessories are available for the Paslode Impulse 18 ga. Brad Nailer: No-Mar Replacement Tip -Hard Tip Part No. 901048 FILTER No-Mar Replacement Tip -Soft Tip Part No. 901067 Battery - Part No. -
Page 19: Troubleshooting
Spark wire out of spark plug. Remove cap and check spark lead, insert in spark plug and replace cover. Spark plug is dirty. Clean tool cylinder head. No spark is generated. Return tool to authorized Paslode ® dealer for service. - Page 20 ® If tool will not operate after following the above service directions, return the tool to an authorized Paslode representative for service. For technical support call 1-800-387-6472 or visit our web site at www.itwconstruction.ca To purchase parts, visit our website at www.itwconstructionparts.com.