Publicité
Les langues disponibles
Les langues disponibles
Operation
Unplug before any adjustment and set up.
Before charging, the lid of charging chambers on the battery
must be opened to enable gas produced during charging to
be released. (Caution! Caustic acid!)
(Not necessary for maintenance-free lead batteries!)
Charging (Fig .3)
•
Connect the charger to the battery to be recharged
•
Always connect the black cable first, to the negative pole.
Connect the red pole cable to the positive pole.
•
The battery should be completely disconnected
from the vehicle before getting down to charging.
•
Always set the charger at the lowest charging degree
(min/1).
•
Now, plug in and control the charging degrees upwards
until charging current equal to ca 10% of the battery
capacity is displayed.
•
Charging degrees may be increased by falling charging
current.
•
Do not disconnect the battery from terminals later than 3-
5 hours after charging is finished.
•
Notice. The charging current indicator will not
come back to zero after charging is finished.
Charging Time
•
The charging time always depends on the battery status
(nearly charged, half-charged or completely discharged)
•
To recover a battery that is normally in use 2 – 4 hrs are
sufficient, while for full recharging 8-10 hrs are needed.
•
Charging time should not be exceeded (10 hrs
max.).
Slow charging
1.
Put the „Mode" change-over switch in position
2.
Turn „Level" changeover switch to the required current value
(visible on the unit)
Note: The „Level" changeover switch is used for charging current
control type of battery to be charged. Typically, a values is
selected to be one tenth of the battery capacity. 100 Ah batter,
charging set-up 10-15 A. It is recommended to reset after several
hours as the battery tends to receive less during the charging
phase and the initially se charging current needs to be restored.
The maximum current power is achieved at position 6. It is
recommended to set the current at maximum only when it is
inevitable. Try starting with the changeover switch at 4/5 position.
Fast Charging with pre-set charging time
1.
Put the „Mode" change-over switch in position
2.
Put the „Level" change-over switch in as far as to the
required current value
3.
Preset the charging time using the timer
Start-up Assistance
CAUTION! At the startup process can overvoltages
arise, the on-board electronics could damage their vehicle.
Please discuss with your automotive specialist.
•
Connect the batteries as shown in part "Charging" and
leave it connected to the vehicle!
•
On principle, two persons should always start up a
vehicle with chargers.
•
The first person shall push the Start button on the
charger (Fig. 3/9, 10). The other one shall immediately
start the ignition.
•
As the vehicle starts up, stop starting immediately, max.
9-10 sec.
•
If the attempt to start fails, wait about 5 minutes for the
charger to get cooled and only then begin another
attempt to start.
Tip: If you change the battery for 10-15 minutes to
subpoena requires much less battery power startup.
Warning: The fuses may burn through and the
vehicle damaged if the starting time is more than 10 s.
Note: The terminals may not touch.
Notice: The charger is equipped with overload
protection.
IMPORTANT NOTICE!: Replacement fuses, the resistance
values of which are dirrerent from the plate values, may
cause material and personal damage. The fuses
replacement should not be done unless the mains cable
is unplugged
Operator Safety Instructions
•
Any safety and protection devices must be fitted in
place before switching the unit on.
•
It is forbidden to attempt starting vehicles, the batteries
of which are discharged or damaged as that would
result in damaging the unit.
•
Any attempts to start in position "charging" instead of
"starting" could damage the ammeter and start the
overload protection.
•
Before pressing the main switch, make sure that the
unit is connected correctly.
•
Warning! If in doubt, consult a specialist in an
authorized servicing centre.
•
Do not use the unit until you have read the manual
carefully.
•
Observe all the safety regulation in this manual.
•
Be responsible to the others.
Step-by-step Instruction
Charging
1.
Connect the charger .
2.
Set the charging function up (min/1).
3.
Switch the charger on .
4.
Plug in .
5.
Battery is being charged. (max. 10 hrs)
Starting
1.
Connect the charger .
2.
Set the starting up (Fig. 3/9, 10).
3.
Connect to the mains.
4.
Switch the charger on and start the vehicle immediately.
5.
As soon as the vehicle is up, stop starting and switch off
and disconnect the charger.
Troubles-Causes-Troubleshooting
Notice: Always check the overload protection first!
Overload circuit-breaker:
1.
Connect the red clamp to the positive pole and the black
one to the negative pole.
2.
Remove the contact and check the fuses.
3.
Set the charger at the lowest charging degree. .
4.
If the battery power input is too high, it is recommended
to have the battery charging done by a skilled electrician
and to keep the level of charge high by frequent
charging or to get a more powerful charger.
Have the battery checked by a specialist. Replace the
battery.
12
Publicité
