Cleaning And Maintenance; Storing The Product; Product Disposal - Chicco CosmoS Notice D'instructions

Child Car Seat, and that the crotch strap is in the cor-
rect position.
• Take the harness and join the two buckle tabs. (Diag. 31)
• Firmly push the two joined buckle tabs inside the
buckle, until a "click" is heard. To ensure maximum
safety, the two buckle tabs have been designed so
as to prevent the locking of a single tab, or one tab
at a time. (Diag. 32)
• To tension the safety harness of the Child Car Seat,
pull the adjustment strap G of the harness, until the
harness straps adhere to the child's body correctly.
(Diag. 33)
WARNING! Do not over-tighten the harnesses: If you
can insert one finger between the harness and your
child's shoulders, it means that it is tightened correctly.
WARNING! Check that the harness is not twisted.

CLEANING AND MAINTENANCE

All cleaning and maintenance operations must only
be carried out by an adult.
HOW TO CLEAN THE FABRIC COVER
The fabric cover of the Child Car Seat can be removed
and cleaned by hand or in a washing machine at 30°C.
Please refer to the following care label symbols for in-
structions on how to clean the fabric cover:
Never use abrasive detergents or solvents. Do not spin
the fabric cover, let it dry without wringing. To remove
the fabric cover, it is first necessary to remove the sa-
fety harness. To carry out this operation, see the points
described from Diag. 20 to Diag. 23 in the "HOW TO
ADJUST THE HEIGHT OF THE SAFETY HARNESS" para-
graph:
Once the safety harness has been removed from the
backrest:
• Take off the fabric cover from the seat of the Child
Car Seat, removing the shoulder straps and the two
harness straps from the respective holes, located on
the fabric cover. (Diag. 34)
To replace the fabric cover and harness straps, pro-
ceed as follows:
• Fit the fabric cover on the seat of the Child Car Seat,
inserting the two harness straps inside the respective
holes, located on the corresponding points of the
fabric cover. (Diag. 35) Then carry out the operations
described from Diag. 26 to Diag. 29, in the "HOW TO
ADJUST THE HEIGHT OF THE SAFETY HARNESS" pa-
ragraph.
WARNING! Check that the harness is not twisted.
HOW TO CLEAN THE
PLASTIC OR METAL PARTS
Clean the plastic and coated metal parts only with a
damp cloth. Never use abrasive detergents or solvents.
The movable parts of the Child Car Seat must not be
lubricated.
30° C
30° C
CHECKING THE CONDITION
OF THE COMPONENTS
It is recommended to check regularly the condition of
the following components to ensure that they are not
damaged or worn out:
• Fabric cover: Check that the padding does not come
out from the seams. Check the condition of the se-
ams: they must always be intact and undamaged.
• Harness: Check that the fabric weft is not frayed or
the harness strap worn out in the parts correspon-
ding to the adjustment strap, crotch, shoulders and
harness adjustment plate.
• Plastic parts: Check that the plastic parts are not worn
out, damaged or faded.
CAUTION! If the Child Car Seat is deformed or worn
out, it must be replaced: it may no longer comply with
the original safety standards.

STORING THE PRODUCT

When it is not fitted into the car, it is recommended
to store the Child Car Seat in a dry place, away from
sources of heat and to protect it from dust, humidity
and direct sunlight.

PRODUCT DISPOSAL

When the Child Car Seat no longer complies with the
original safety standards, stop its use and dispose of it
at an appropriate collection point. Dispose of the pro-
duct as laid down in the environmental norms in force
in the Country of use.
14
Machine washable at 30°
Do not bleach
Do not spin dry
Do not iron
Do not dry clean