Bench Grinder Safety Warnings; Mains Connection - Güde GKS 150-25 Traduction Du Mode D'emploi D'origine

from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction of
a second.
3) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in
unexpected situations.
4) Service
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.

Bench grinder safety warnings

a) Do not use a damaged accessory. Before each
use, inspect the accessory such as abrasive
wheels for chips and cracks. After inspecting
and installing an accessory, position yourself
and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dama-
ged accessories will normally break apart during this
test time.
b) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
c) Never grind on the sides of a grinding wheel.
Grinding on the side can cause the wheel to break
and fly apart.
Risk of injury!
Keep body parts and clothes away from rotating
parts of the device.
Only transport the device when the mains plug has
been disconnected.
Always ensure that the device is adequately stable
and secured.
Carry out a visual inspection before switching the
appliance on.
Check especially the safety equipment, electrical
control elements, power lines and screw couplings for
any damage and if they are tightened appropriately. If
necessary, replace damaged parts before operation.
Always use the power tool with insertion tools on
both spindles to minimise the risk of making contact
with the rotating spindles.
Please note the instruction on safely carrying out
grinding functions.
Replace damaged or heavily rutted grinding discs.
In the event of a blockage, switch off the machine
immediately.

Mains Connection

Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Connect only to a single-phase AC current supply
and only to the mains voltage specified on the rating
plate. Must only be used from sockets with earth wire.
Only plug-in when machine is switched off.
ENGLISH
23