Adjusting The Grinding Table Angle (Fig. 5); Connecting The Dust Exhaust (Fig. 6); Working With The Tg 125/E Disc Grinding Machine; Working With The Angle Stop (Fig. 7) - Proxxon TG 125/E Traduction De La Notice D'utilisation Originale

Masquer les pouces Voir aussi pour TG 125/E:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
Please note in general:
Proxxon bits and cutters have been designed to work
with our machines, which makes them optimal for
their use.
We will not assume any liability whatsoever for the
safe and proper function of our devices when using
third-party bits and cutters!
5.4 Adjusting the grinding table angle
(fig. 5):
Before adjusting the grinding table, always discon-
nect the mains plug to prevent the disc being started
up accidentally. Risk of injury!
1. Loosen rotary knob 1 At the same hold rotary
knob 2
2. Swing grinding table 3 into the desired angle posi-
tion and check the set value on angle scale 4.
3. Tighten rotary knob 1. At the same hold rotary
knob 2

5.5 Connecting the dust exhaust (fig. 6):

Before connecting the dust exhaust, always discon-
nect the mains plug to prevent the disc being started
up accidentally. Risk of injury!
It is recommended to always work with the dust
exhaust! This not only guarantees clean working, it
also reduces the hazardous effect of some dusts!
1. Push adapter piece 1 onto connecting piece 2 of
the machine
2. Push rubber adapter 3 onto adapter piece 1
3. Insert vacuum cleaner nozzle 4 into rubber
adapter 3
4. Switch on vacuum cleaner when working
Another small tip:
When using the Proxxon CW-matic vacuum cleaner,
manual switching on and off is no longer necessary.
The CW-matic is fitted with an automatic control
device; it automatically switches on and off when the
power tool is switched on and off. The same effect
can be obtained with traditional vacuum cleaners by
using our vacuum control device.
- 14 -
Caution:
Caution:
6
Working with the TG 125/E disc grinding
machine
Please note that the grinding disc turns to the left! If
you use the left side when working with the attached
grinding table, the work piece can be guided easily
and securely, thus effectively preventing it from being
hurled away!
When grinding metallic work pieces, such as when
grinding knife blades for example, or when grinding
stone or ceramics the material to be ground can
become very hot! Do not hold the material to be
ground near the grinding surface in order to avoid
burns!
Wear suitable gloves to avoid abrasions especially
when working with coarse sandpaper and when pro-
cessing smaller work pieces!
1. If mitres are to be ground, adjust the grinding
angle as described above
2. Insert the mains plug
3. Switch on the machine at On-Off-Switch
4. Set the required speed on the speed control but-
ton (pos. 3, fig. 1)
Please adjust the size of the work piece to the size of
the machine! A work piece that is too large and too
heavy can overburden the drive or the construction of
the machine and cause damage or injuries!

6.1 Working with the angle stop (fig. 7):

If, for example, the ends of somewhat thinner strips
are ground for mitre, it is advantageous to use the
angle stop included in the scope of delivery.
1. Loosen knurled screw 1
2. Set the desired angle on scale 2
3. Turn the knurled screw tightly and insert into the
intended table groove
4. Guide the desired workpiece up to the stop
against the grinding wheel as shown in the illus-
tration
Caution:
Caution:
Caution:

Publicité

Table des Matières
loading

Table des Matières