Self Help - Thermador DWHD650G Série Instructions D'installation

Dishwashers may occasionally exhibit problems unrelated to a malfunction of the dishwasher itself.
The following information may help you with a dishwasher problem without involving a repair professional.
Problem Cause
Dishwasher 1. Door may not be properly latched.
does not start 2. Unit may not be turned on.
3. Unit not reset or previous cycle not completed.
4. Delay start engaged.
5. Interruption of electrical power supply to dishwasher or
blown fuse.
6. The door may have been closed without irst selecting a
cycle.
7. Water supply may not be turned on.
Dishwasher Default factory settings alert the customer that the cycle has
beeping (end of completed by beeping. This feature can be deactivated if so
cycle signal) desired.
Display does 1. A fuse may have been blown or circuit breaker tripped.
not illuminate 2. Door not closed or latched.
or console Note: For models with controls on the top portion of the door,
lights are not on the display only illuminates when the door is opened and con-
trols are visible.
Dishwasher 1. Incoming water is not warm enough.
seems to run a 2. Cycle time can vary due to soil and water conditions.
long time 3. Rinse agent dispenser is empty.
4. Dishwasher connected to cold water supply.
Note: Refer to the cycle chart (pg.14) in the "Wash cycle infor-
mation" section of this manual for typical cycle length.
Dishes are not 1. Spray arm movement is obstructed.
getting clean 2. Spray arm nozzles clogged.
enough 3. Improper use of detergents.
4. Filters could be clogged.
5. Dishes are nested or loaded too close together.
6. Selected wash cycle is not suitable for food soil cond-
tions.
Dishes are not 1. Rinse agent dispenser is empty. (Rinse agent indicator is
getting dry activated).
enough 2. Improper loading of dishes.
3. Selected cycle does not include drying.
Note: Plastic or Telon do not typically dry as completely as
other items due to their inherent properties.
Odor 1. Food debris is present at the bottom of the dishwasher.
2. Food particles are present near the door seal.
3. Residual water is present at the bottom of the dishwasher.
4. Drain hose is obstructed.
21

SELF HELP

Action
1. Shut the door completely.
2. Press the main power switch to turn unit on.
3. To reset, refer to "Interrupting the cycle" (pg.17) in the "Operating the
unit" section of this manual.
4. To reset, refer to "Delay start" (pg.16) in the "Additional features" section
in this manual.
5. Check circuit breaker.
6. Select a cycle and close the door.
7. Check and turn on water supply.
To adjust the volume or deactivate, refer to "Cycle completion signal" (pg.16)
in the "Additional features" section in this manual.
1. Check the fuse or circuit breaker box and replace the fuse or reset the
breaker if necessary.
2. Ensure that door is properly latched and completely closed.
1. Before starting a cycle, run hot water faucet at the sink nearest to the
dishwasher.
2. Sensors in the dishwasher automatically increase the cycle time to en-
sure a good wash when heavy soil is detected.
3. Add rinse agent.
4. Verify dishwasher is connected to hot water supply plumbing.
1. Ensure that spray arm movement is not blocked by hand rotating spray
arms.
2. Remove the spray arms and clean according to "Spray arms" (pg.18) in
the "Maintenance and care" section of this manual.
3. Increase or decrease detergent depending on the water hardness. Refer
to the table under "Detergent" (pg.7).
4. Clean the ilter. Refer to "Filters" (pg.18) in the "Maintenance and care"
section of this manual.
5. Rearrange load such that water spray can reach all items in the dish-
washer. See also "Loading your dishwasher" (pg.10) .
6. Refer to the "Wash cycle information" (pg.14) section of this
1. Add rinse agent. The use of rinse agent improves drying.
2. Rearrange load to ensure items are not nested. Refer also to the "Load-
ing your dishwasher" (pg.10) section of this manual.
3. Refer to "Wash cycle information" (pg.14).
Note: Select models ofer an extra heating options to improve drying per-
formance. Refer to "Wash cycle information" (pg.14) section of this manual.
1. Remove the ilters and clean according to "Filters" (pg.18) in the "Main-
tenance and care" section of this manual.
2. Regulary clean door seals with damp cloth.
3. Ensure the unit has completely drained from the last cycle. Refer to "Ter-
minating the cycle" (pg.17) in the "Operating the unit"
section of this manual.
4. Remove any obstructions from the drain hose by calling qualiied per-
sonnel.
Note: If odor still persists, run the Normal cycle until it lushes and interrupt
the cycle and place an 8 oz. cup of distilled white vinegar solution on the top
rack and then inish the cycle.
manual.