Know Your Product; Operation - SPARKY HD PROFESSIONAL MKL 800CES Plus Notice Originale

snagging the accessory. Corners, sharp
edges or bouncing have a tendency to
snag the rotating accessory and cause loss
of control or kickback.
с) Do not attach a toothed saw blade. Such
blades create frequent kickback and loss of
control.
d) Always feed the bit into the material in
the same direction as the cutting edge
is exiting from the material (which is the
same direction as the chips are thrown).
Feeding the tool in the wrong direction
causes the cutting edge of the bit to climb
out of the work and pull the tool in the direc-
tion of this feed.
е) When using rotary files, cut-off wheels,
high-speed cutters or tungsten carbide
cutters, always have the work securely
clamped. These wheels will grab if they be-
come slightly canted in the groove, and can
kickback. When a cut-off wheel grabs, the
wheel itself usually breaks. When a rotary
file, high-speed cutter or tungsten carbide
cutter grabs, it may jump from the groove
and you could lose control of the tool.
Additional safety instructions for grind-
ing and cutting-off operations
а) Use only wheel types that are recom-
mended for your power tool and only
for recommended applications. for ex-
ample: do not grind with the side of a
cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces
applied to these wheels may cause them to
shatter.
b) for threaded abrasive cones and plugs
use only undamaged wheel mandrels
with an unrelieved shoulder flange that
are of correct size and length. Proper
mandrels will reduce the possibility of
breakage.
с) Do not "jam" a cut-off wheel or apply
excessive pressure. Do not attempt to
make an excessive depth of cut. Over-
stressing the wheel increases the loading
and susceptibility to twisting or snagging of
the wheel in the cut and the possibility of
kickback or wheel breakage.
d) Do not position your hand in line with
and behind the rotating wheel. When the
wheel, at the point of operation, is moving
away from your hand, the possible kick-
back may propel the spinning wheel and
the power tool directly at you.
Original instructions
е) When wheel is pinched, snagged or
when interrupting a cut for any reason,
switch off the power tool and hold the
power tool motionless until the wheel
comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut
while the wheel is in motion otherwise
kickback may occur. Investigate and take
corrective action to eliminate the cause of
wheel pinching or snagging.
f) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power
tool is restarted in the workpiece.
g) Support panels or any oversized work-
piece to minimize the risk of wheel pinch-
ing and kickback. Large workpieces tend
to sag under their own weight. Supports
must be placed under the workpiece near
the line of cut and near the edge of the
workpiece on both sides of the wheel.
h) Use extra caution when making a "pock-
et cut" into existing walls or other blind
areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that
can cause kickback.

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Nut
2. Collet
3. Spindle
4. ON/OFF switch
5. Cord with plug
6. Electronic regulator of speed

Operation

This power tool is supplied from single-phase al-
ternating current mains only. It is double insulat-
ed according to EN 60745-1 and IEC 60745 and
can be connected to grounded or not grounded
sockets. This power tool is radio suppressed in
compliance with EMC Directive.
7
EN