Safety Warnings Specific For Wire Brushing Operations; Know Your Product; Operation; Prior To Initial Operation - SPARKY HeavyDuty M 2000 HD Notice Originale

the cut-off wheel from the cut while the
wheel is in motion otherwise kickback
may occur. Investigate and take corrective
action to eliminate the cause of wheel bind-
ing.
d) Do not restart the cutting operation in
the workpiece. Let the wheel reach full
speed and carefully re-enter the cut. The
wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
e) Support panels or any oversized work-
piece to minimize the risk of wheel pinch-
ing and kickback. Large workpieces tend
to sag under their own weight. Supports
must be placed under the workpiece near
the line of cut and near the edge of the
workpiece on both sides of the wheel.
f) Use extra caution when making a "pock-
et cut" into existing walls or other blind
areas. The protruding wheel may cut gas
or water pipes, electrical wiring or objects
that can cause kickback.
Safety Warnings Specific for Sanding
Operations:
a) Do not use excessively oversized sand-
ing disc paper. follow manufacturer's
recommendations,
sanding paper. Larger sanding paper ex-
tending beyond the sanding pad presents
a laceration hazard and may cause snag-
ging, tearing of the disc or kickback.
Safety Warnings Specific for Wire
Brushing Operations:
a) Be aware that wire bristles are thrown
by the brush even during ordinary op-
eration. Do not overstress the wires by ap-
plying excessive load to the brush. The wire
bristles can easily penetrate light clothing
and/or skin.
b) If the use of a guard is recommended for
wire brushing, do not allow any interfer-
ence of the wire wheel or brush with the
guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal
forces.

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
M 2000 HD●MB 2000P HD●MA 2000 HD●MBA 2000P HD●M 2200 HD●MB 2200P HD●MA 2200 HD●MBA 2200P HD
8
EN
when selecting
M 2400 HD●MB 2400P HD●MA 2400 HD●MBA 2400P HD●MB 2600P HD●MBA 2600P HD
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Spindle
2.1. Grinding wheel (Use only with
a wheel guard for grinding wheel!)*
2.2. Cutting wheel (Use only with
a wheel guard for cutting wheel!)*
3.1. Wheel guard for grinding wheel
3.2. Wheel guard for cutting wheel*
4. Support flange
5. Fixing flange
6. Auxiliary handle
7. ON/OFF switch
8. ON/OFF switch locking button
9. Spindle lock button
ACCESSORIES TO BE USED WITH
THIS POWER TOOL
10. Wire cup brush*
11. Plastic (rubber) backing pad*
12. Sandpaper*
13. Lock nut*
* The additional accessories shown in the illus-
trations or described in the text are not included
in the delivery.

Operation

These power tools are supplied from single-
phase alternating current mains only. They
are double insulated according to EN 60745,
IEC 60745-1 and can be connected to grounded
or not grounded sockets. This power tool is ra-
dio suppressed in compliance with EMC Direc-
tive 2004/108/EC.
This power tool is designed for cutting, grinding
and brushing mainly metals without using wa-
ter.

PRIOR TO INITIAL OPERATION

▪ The machine may be delivered with the wheel
guard mounted at the factory. Ensure that the
wheel guard is mounted properly and fixed
reliably prior to the initial and any following
operation.
▪ The machine may be delivered with the wheel
mounted at the factory. Ensure that the wheel
is mounted properly and fixed reliably prior to
the initial and any following operation.
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.