Know Your Product; Operation; Prior To Initial Operation; Wheel Replacement - SPARKY MBG 125L Notice Originale

vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
WARNING: The use of any accessories or at-
tachments differing from the recommended herewith
may present a risk of injury for the operator.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. LED light
2. Eye shield support
3. Nut
4. Eye shield
5. Grinding wheel
6. Tool rest
7. Adjusting nut
8. Rubber pad
9. ON/OFF switch
10. Base
11. Wheel guard

Operation

This power tool is supplied from single-phase alternating
current mains only. This power tool is Class I according
to EN 61029 -1 and must not be fitted to sockets with-
out protective earthing. This power tool is radio sup-
pressed in compliance with EMC Directive 2004/108/
EC and with EN 55014-1, EN 55014-2, EN 61000-3- 2,
EN 61000- 3-3.
The bench grinder is designed for grinding, sharpening
and finishing operations: sharpening of all kind of tools,
cleaning metal surfaces and metal sections by means of
corundum grinding wheels.

PRIOR TO INITIAL OPERATION

WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance, including wheel replacement.
▪ Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
Original Instructions
data of the tool.
▪ Connect the power tool to a socket with protective
earth contact only.
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position. If the
plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
▪ If the supply cord is damaged it must be replaced with
a special cord or assembly available from the manu-
facturer or its service agent to avoid a safety hazard.
▪ At low temperatures or when the machine has not
been used for a long time, let the machine operate at
no load for a while.
▪ Place the bench grinder firmly on a flat workbench.
The power tool can be fastened to a work bench (Fig.1)
or special stand SBG 80 (delivered separately) by M10
bolts. The bench grinder stand SBG 80 can be fas-
tened to the floor by means of two M12 bolts (Fig.2).
ASSEMBLY
WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance.
Inspect visually the grinding wheels (5) for mechanical
damages.
▪ Check all fasteners. Ensure that the screws fixing the
wheel guards are securely tightened.
▪ Install the tool rests (6) and adjust their position. The
distance between the tool rest (6) and the wheel (5)
must no exceed 1.6 mm. Tighten the adjusting nuts
(7).
▪ Mount the eye shield supports (2). During normal
operation the operator must have a clear view of the
grinding wheels (5) through the eye shields (4).
WARNING: Never operate the bench grinder
without the wheel guards and the eye shields.

WHEEL REPLACEMENT

WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance, including wheel replacement.
WARNING: Use only grinding wheels with di-
mensions and peripheral speed, corresponding to the
specification of the bench grinder.
To replace a grinding wheel perform the following opera-
tions:
1. Inspect the new grinding wheel for visible defects.
Then insert your forefinger into the wheel arbor and
5
EN