SPARKY HD PROFESSIONAL MKL 800CES Plus Notice Originale page 8

broken accessory may fly away and cause
injury beyond immediate area of operation.
k) Hold power tool by insulated gripping
surfaces only, when performing an op-
eration where the cutting accessory may
contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire
may make exposed metal parts of the pow-
er tool "live" and could give the operator an
electric shock.
l) Always hold the tool firmly in your
hand(s) during the start-up. The reaction
torque of the motor, as it accelerates to full
speed, can cause the tool to twist.
m) Use clamps to support workpiece when-
ever practical. Never hold a small work-
piece in one hand and the tool in the
other hand while in use. Clamping a small
workpiece allows you to use your hand(s)
to control the tool. Round material such as
dowel rods, pipes or tubing have a tenden-
cy to roll while being cut, and may cause
the bit to bind or jump toward you.
n) Position the cord clear of the spinning
accessory. If you lose control, the cord
may be cut or snagged and your hand or
arm may be pulled into the spinning acces-
sory.
o) Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the sur-
face and pull the power tool out of your con-
trol.
p) After changing the bits or making any
adjustments, make sure the collet nut,
chuck or any other adjustment devices
are securely tightened. Loose adjustment
devices can unexpectedly shift, causing
loss of control, loose rotating components
will be violently thrown.
q) Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your cloth-
ing, pulling the accessory into your body.
r) Regularly clean the power tool's air
vents. The motor's fan will draw the dust
inside the housing and excessive accumu-
lation of powdered metal may cause electri-
cal hazards.
s) Do not operate the power tool near flam-
mable materials. Sparks could ignite these
materials.
t) Do not use accessories that require liq-
uid coolants. Using water or other liquid
coolants may result in electrocution or
shock.
6
EN
▪ The tool must be used only for its pre-
scribed purpose. Any use other use than
those mentioned in this Instruction will be
considered a case of misuse. The user and
not the manufacturer shall be liable for any
damage or injury resulting from such cases
of misuse.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any dam-
age resulting from such changes.
▪ When operating in dusty environment, the
ventilation slots must be kept clean. If it
should become necessary to clear dust,
first disconnect the tool from the mains sup-
ply (use non metallic objects to clean the
dust) and avoid damaging internal parts.
The power tool will overheat under deterio-
rated cooling due to the clogged with dust
ventilation slots.
▪ The power tools must not be used outdoors
in rainy weather, or in moist environment
(after rain) or in close vicinity with easily
flammable liquids and gases. The working
place should be well lit.
further safety instructions for all op-
erations
Kickback and related warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, sanding band, brush
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the ac-
cessory's rotation.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/
or incorrect operating procedures or conditions
and can be avoided by taking proper precau-
tions as given below.
а) Maintain a firm grip on the power tool
and position your body and arm to allow
you to resist kickback forces. The opera-
tor can control kickback forces, if proper
precautions are taken.
b) Use special care when working corners,
sharp edges etc. Avoid bouncing and
MKL 800CES Plus