Concrete Grinder Safety Warnings; Know Your Product; Operation - SPARKY HD Professional FB 514 Notice Originale

5. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Concrete grinder
safety warnings
WARNING: Before connecting a tool to a power
source be sure that the voltage supply is the same as that
specified on the nameplate of the tool.
▪ A power source with a voltage greater than that speci-
fied for the tool can result in serious injury to the user,
as well as damage to the tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
Always wear eye and ear protection
and use a dust mask. The dust and abrasive particles
separated during operation may seriously injure your
health.
▪ Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
▪ Always switch off and unplug the power tool prior
to any adjustment, servicing or maintenance.
▪ The outer metal parts and the bits may get hot after
continuous operation.
▪ Use clamps or a vice to secure your work whenever
possible.
▪ Always switch off the machine and wait until the spin-
dle has come to a complete standstill before placing
it down.
▪ Do not force the machine: let the tool do the work at a
reasonable speed. Overloading will occur if too much
pressure is applied and the motor slows resulting in
inefficient work and possible damage to the motor.
▪ Rags, cloths, cord, string and the like should never be
left around the work area.
▪ Remove any nails, screws, etc. from the processed
surface.
▪ Before using the tool on an actual work piece, switch
on and let it run for a while. Operate the tool at least
200 mm away from your face and body.
▪ Always be sure you have a firm footing. Be sure no
one is below when using the tool in high locations.
▪ Hold the power tool firmly.
▪ Keep your hands away from rotating parts. Do not
touch the bit or the work piece immediately after op-
eration - they may be extremely hot and you may get
serious burns.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
Original instructions
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operat-
ing instructions found in this Manual. All persons who
use and service the machine have to be acquainted
with this Manual and must be informed about its po-
tential hazards. Children and frail people must not use
this tool. Children should be supervised at all times if
they are in the area in which the tool is being used. It
is also imperative that you observe the accident pre-
vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
Even when the tool is used as prescribed it is not pos-
sible to eliminate all residual risk factors. The following
hazards may arise in connection with the tool's construc-
tion and design:
▪ Damage to hearing if effective hearing protection is
not worn.
▪ Always unplug the machine prior to any adjustment,
servicing or maintenance including replacing the ac-
cessories.
▪ The power tools must not be used outdoors in rainy
weather, or in moist environment (after rain) or in close
vicinity with easily flammable liquids and gases. The
working place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Spindle
2. Wheel guard
3. Base support washer
4. Diamond cup wheel
5. Flat support washer
6. Lock nut
7. ON/OFF switch
8. Spindle lock button
9. Brush shield
10. Fastening bracket
11. Auxiliary handle
12. Lock nut wrench
13. Screw

Operation

This power tool is supplied from single-phase alternating
current mains only. It is double insulated according to EN
60745-1, IEC 60745 and can be connected to grounded
or not grounded sockets. This power tool is radio sup-
pressed in compliance with EMC Directive 2004/108/
EC.
5
EN