• Remove the battery pack.
• Adjust the "cutting diameter slide"
on the grass deflector to adjust the
cutting path diameter. There are 2
diameter options: 30cm, 25cm.
NOTE a small diameter cutting pathe
will maximize run time and cutting speed,
while a larger cutting pathe will help
complete the trimming task quicker.
LINE CUT-OFF BLADE
See Figure 10.
This trimmer is equipped with a line cut-off
blade on the grass deflector. For best cutting,
advance line until it is trimmed to length by the
line cut-off blade. Advance line whenever you
hear the engine running faster than normal,
or when trimming efficiency diminishes. This
will maintain best performance and keep
line long enough to advance properly.
When servicing, use only
identical replacement parts.
Use of any other parts may create a
hazard or cause product damage
To avoid serious personal injury, always
remove the battery pack from the tool when
cleaning or performing any maintenance.
Before each use, inspect the entire product
for damaged, missing, or loose parts such as
screws, nuts, bolts, caps, etc. Tighten securely
all fasteners and caps and do not operate this
product until all missing or damaged parts are
replaced. Avoid using solvents when cleaning
plastic parts. Most plastics are susceptible
to damage from various types of commercial
solvents and may be damaged by their use.
Use clean cloths to remove dirt,
dust, oil, grease, etc.
Do not at any time let brake
fluids,gasoline, petroleum-based
products, penetrating oils, ect.come in
contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which
may result in seriou personal injury.
Only the parts shown on the parts list are
intended to be repaired or replaced by
the customer. All other parts should be
replaced at an Authorised Service Centre.
Upon removal, cover the battery
pack's terminals with heavy-duty
adhesive tape. Do not attempt to destroy
or disassemble battery pack or remove
any of its components. Lithium-ion and
nickel-cadmium batteries must be recycled
or disposed of properly. Also, never
touch both terminals with metal objects
and/or body parts as short circuit may
result. Keep away from children. Failure
to comply with whese warning s could
result in fire and.or serious injury.
SPOOL REPLACEMENT
See Figure 12.
Use original manufacturer's replacement
cutting line for best performance.
• Remove the battery pack.
• Push in tabs on side of spool cover.
• Pull spool cover up to remove.
• Remove the old spool.
• To install the new spool, make sure the
cutting line is captured in the slot on the new
spool. Make sure the end of the cutting line is
extended approximately 15cm beyond the slot.
• Install the new spool so that the cutting line
and slot align with the eyelet in the cutting
head. Thread the cutting line into the eyelet.
• Pull the cutting line extending from
the cutting head so the cutting line
releases from the slot in the spool.
• Reinstall the spool cover by depressing
tabs into slots and pushing down until
spool cover clicks into place.
CUTTING LINE REPLACEMENT
See Figures 12 - 13.
• Remove the battery pack.
• Remove the spool from the cutting head.
NOTE Remove any old cutting
line remaining on the
spool.
• Cutting a piece of cutting line
approximately 3m long.
• Insert the cutting line into the anchor hole
in the upper part of the spool. Wind the
cutting line around the upper part of the
spool clockwise, as shown by the arrows
on the spool. Place cutting line in theslot
on upper spool flange, leaving about 15cm.
Extended beyond the slot. Do not overfil.
After winding the cutting line, there should be
at least0.635cm between the wound cutting
line and the outside edger of the spool.
• Replace the spool, and the spool cover. Refer
to spool replacement earlier in this manual.
STORING THE TRIMMER
• Remove the battery pack from
the trimmer before storing.
• Clean all foreign material from the trimmer.
• Store it in a place that is
inaccessible to children.
• Keep away from corrosive agents such as
garden chemicals and de-icing salts.
EN - 7