Installation Site; Electrical Connection - Sammic CA-301 Mode D'emploi

Each machine is identified as follows:
- Name and address of the manufacturer: SAM-
MIC S.L - Basarte 1 Azkoitia. Gipuzkoa (SPAIN)
- The serial number is printed on the Guarantee
Card and in the Declaration of Conformity.
MODELS
This manual describes the installation, opera-
tion and maintenance of vegetable preparation
machines CA-301, CA-401 and CA-601. The
model reference number and its features are
specified on the name plate attached to the
machine. This preparation machine has been
designed and manufactured in accordance with
the following European directives:
- Machinery Directive 2006/42/EC.
- Low Voltage Directive 2006/95/EC.
- Electromagnetic Compatibility
2004/108/EC.
- Directives 89/109/EEC and 90/128/EEC on
aluminium and plastic materials and articles in
contact with food.
- Aluminium alloys in contact with food standard
EN 601-2004.
- Hygiene and food contact materials standard:
ANSI-NSF 8 and ANSI-NSF 51.
- Vegetable Preparation Machines Standard:
UNE-EN1678
- Protection level in accordance with UNE-EN
60529: Controls IP-55 and rest of machine IP-23.
- The 120V/60Hz/1~ models comply with the
UL-763 and CSA C22.2 standards
INSTALLATION
For optimum service and maintenance, please
follow these instructions.

INSTALLATION SITE

You are advised to install the machine on a
steady surface -this must not act as a sound-
board- elevated at a height of 700-900 mm for
CA-301, 600-800 mm for CA-401 and 500-700
mm for CA-601. Place the collector underneath
the food outlet. The machine is not fixed in
place and can be moved around easily.

ELECTRICAL CONNECTION

Check that the machine's electrical charac-
teristics match the mains power supply.
Single-phase machines: 230V / 50 Hz / 1; 220V
/ 60 Hz / 1; 120V / 60 Hz / 1.
Prepare a wall-mounted socket that is always
accessible, with a general disconnecting switch
and with a residual current and 2P, 16 A circuit
breaker, with its corresponding plug.
6
EN
Three-phase machines: 230-400V / 50 Hz / 3N
(connected to 400V); 220-380V / 60 Hz / 3N
(connected to 220V).
Prepare a wall-mounted socket that is always
accessible, with a general disconnecting switch
and with a residual current and 2P, 10 A circuit
breaker, with its corresponding plug.
To change the voltage, refer to the electrical
diagram.
Direction of rotation: When the machine's direc-
tion of rotation is incorrect, the disc (A) will not
cut. The disc (A) must rotate anti-clockwise. If
the disc (A) rotates clockwise, to reverse it
swap two phases in the power cable.
Power cable characteristics.
Vegetable preparation machines CA-301, CA-
401 and CA-601 are supplied with a 1.5 m ther-
moplastic-sheathed power cable.
WARNING: THE EARTH CONNECTION IS
Directive OBLIGATORY. DANGER OF ELECTROCUTION.
The machine's earth wire is yellow-green.
ELECTRONIC CONTROL FUNCTIONS AND
OPERATION
See Fig. 1.
"Machine connected to mains" warning light (1).
When the machine is plugged in, this warning
light switches on to show that the machine is
connected to the mains.
See Fig. 1.
"Start" button (3) or slow speed in the 2-
speed model.
CA-301 and CA-401:
- With the hinged lid (I) closed and the pusher plate
(L) down, if you push this button the motor starts.
In the 2-speed models it starts at slow speed.
- With the motor stopped, the hinged lid (I)
closed and the pusher plate (L) up, if you
press this button, the "safety" light (2) flashes.
When the pusher plate (L) is pressed down
the motor starts.
- With the motor stopped, the hinged lid (I)
closed and the pusher plate (L) up, if you
press this button, when the pusher plate is
lowered (L) the motor starts. In the 2-speed
models the pilot light "Speed 1" (5) flashes.
- With the motor on, if you lift the pusher plate
(L) the motor stops. When you lower the push-
er plate (L), the motor re-starts automatically.
If the pusher plate (L) has not lowered in 30
seconds, the "Start" button (3) must be
pressed again to start the machine.
- With the motor on, if the hinged lid (I) is
opened the motor stops. When the hinged lid
(I) is closed, the "Start" button (3) needs to be
pressed again to start the machine.
- If the machine is left running with the pusher
plate (L) down, after 30 minutes the machine
stops automatically.
CA-601 and header:
- If this button is pressed whilst the motor is
switched off, the hopper mounted and the
hinged lid (I) closed, the motor starts.
- If the hinged lid (I) should open whilst the motor
is in operation the motor will stop. When closing
the hinged lid (I) the pushbutton "On" (3) must
be pressed again in order to start the machine.
See Fig. 1.
"Speed 2" button (7). Fast speed. Only 2-
speed models.
The operation of this button is identical to that of
the "Start" button (3). The only difference is that
the machine starts at high speed.
See Fig 1.
"Stop" button (4).
This button stops the motor.
See Fig 1.
"Safety" warning light (2).
This warning light shows the machine's status.
- It switches off when the motor is stopped, the
hinged lid (I) is closed and the pusher plate (L)
is down.
- It switches on when the motor is stopped, the
hinged lid (I) is closed and the pusher plate (L) is up.
- In the CA-301 and CA-401 with the hinged lid (I)
closed and the pusher plate (L) up it flashes slowly.
- It flashes quickly when the hinged lid (I) is open.
See Fig. 1.
"Speed 1" pilot light (5). Only in the
2-speed models.
This pilot light provides information on the sta-
tus of the vegetable preparation machine when
starting at slow speed.
- It switches off when the motor is stopped, the
hinged lid (I) is closed and the pusher plate (L)
is down.
- It switches on when the motor is on, the hinged
lid (I) is closed and the pusher plate (L) is down
- In the CA-301 and CA-401 with the hinged lid (I)
closed and the pusher plate (L) up it flashes slowly.