Set Up And Installation - Sammic LM-6 Mode D'emploi

INDICATIONS FOR CE MARKING
Each machine has the following identifiers:
- Manufacturer's name and address:
SAMMIC, S.L. C / Atxubiaga 14 Azpeitia
Gipuzkoa (SPAIN).
- "CE" mark.
- The machine model is indicated in the
following section.
- The serial number is shown in the gua-
rantee sheet and in the compliance note.
MODELS. COMPLIANCE WITH THE REGU-
LATIONS
This manual describes the installation, ope-
ration and maintenance of the LM-6 mussel
washer.
The model and its characteristics are indi-
cated in the nameplate of the machine.
This machine is designed and manufactu-
red in accordance with the following
European directives:
93/68/CEE, 73/23/CEE.

SET UP AND INSTALLATION

To get the best benefits, as well as a suita-
ble conservation of the machine, you must
carefully follow the set up and installations
instructions as well as the user's instruc-
tions contained in this manual.
L
OCATION
Put the machine on a flat, horizontal, rigid
surface to avoid vibrations and noises.
At its location, the machine needs a socket,
a cold water tap and a drainage.
4 ENGLISH
E
LECTRIC CONNECTION
Motor features
This machine is provided with the following
motors:
-LM-6: 370 W three-phase or 370 W single-
phase.
The three-phase motor is supplied for 230
- 400 V / 50 Hz (connected to 400 V) or
220-380 V / 60 Hz (connected to 220 V).
Before connecting the machine to the
mains, check if the motor has the same vol-
tage as the mains. If not, change the volta-
ge. For a voltage change from 400 to 230
V, loose the terminal box. There is a plate
on the cover which
how to do it.
Cable features
SAMMIC machines are supplied with an
electric cable of 1,8 m length and thermo-
plastic coating.
THE CONNECTION TO EARTH IS COMPUL-
SORY. The earth wire of the machine is
marked.
89/392/CEE,
- Three-phase machines: use a 3P+T wall
socket of 16A and a tight plug to connect
it to the cable of the machine.
- Single-phase machines: use a 2P+T wall
socket and its corresponding plug.
Motor rotation
The turntable should turn from left to right.
For safety's sake, check the direction indi-
cated by the arrow at the back of the
machine. To invert the rotation in machines
with three-phase motor, change the posi-
tion of two wires (one in the place of the
other and viceversa).
W
ATER ENTRY
External diameter of input nozzle: Ø 12
mm. Connect the cold water tap through a
hose that can withstand a pressure non
. inferior to 6kg/cm
D
Avoid bend pipes and inclinations that obs-
truct the drainage. Exit diameter for all the
models: Ø 46 mm.
E
XIT
The door for discharging the mussels can
be orientated after loosening the 2 screws
of the cylinder base.
S
UPPORT WITH OR WITHOUT FILTER
explains graphically
LM-6 can be installed on a rigid table or on
a SAMMIC support. We recommend the
support for this model in order to ease the
draining.
OPERATION TERMS. USE
L
OADING OF THE MACHINE
The machine is loaded by lifting the cover
of the machine and loading it with a maxi-
mum of 5 Kg of mussels. The mussels
should not contain other materials that can
damage the machine.
H
UP
The water tap is opened, the timer is set to
the required time and the machine is tur-
ned on.
D
To empty out the machine, a container is
placed in front of the door to collect the
cleaned mussels of similar size. The door is
opened with a hand, and after exerting a
.
2
RAINAGE
D LM-6
OOR FOR MUSSEL WASHER
OW TO PROGRAM THE CYCLE DURATION AND SET
ISCHARGING OF THE MACHINE