Appliance Vent Connection; Horizontal Air Terminal Installation - Napoleon GDS20N Instructions D'installation Et D'opération

20
20
20
4.2

APPLIANCE VENT CONNECTION

4.2 APPLIANCE VENT CONNECTION
4.2 APPLIANCE VENT CONNECTION
A. Attach the adjustable pipe to the last section of rigid pipe. Secure
A.
Attach the adjustable pipe to the last section of rigid pipe. Secure
EN
with screws and seal.
EN
EN with screws and seal.
B. Install the inner ex pipe to the appliance. Secure with 3 screws
B. Install the inner  ex pipe to the appliance. Secure with 3 screws
and at washers. Seal the joint and screw holes using the high
and  at washers. Seal the joint and screw holes using the high
temperature sealant W573-0007 (not supplied).
temperature sealant W573-0007 (not supplied).
C. Run a bead of high temperature sealant (not supplied) around the
C. Run a bead of high temperature sealant (not supplied) around the
inside of the air intake collar. Pull the adjustable pipe a minimum 2"
inside of the air intake collar. Pull the adjustable pipe a minimum 2"
(50.8mm) into the air intake collar.
(50.8mm) into the air intake collar.
NOTE: Ensure that the sealant is not visible on the exterior pipes once
NOTE: Ensure that the sealant is not visible on the exterior pipes once
installation is completed. An optional decorative black band is available
installation is completed. An optional decorative black band is available
for this use. In the event that the venting must be disassembled, care
for this use. In the event that the venting must be disassembled, care
must be taken to reseal the venting.
must be taken to reseal the venting.
4.3

HORIZONTAL AIR TERMINAL INSTALLATION

4.3 HORIZONTAL AIR TERMINAL INSTALLATION
4.3 HORIZONTAL AIR TERMINAL INSTALLATION
TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE
TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE
TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE
DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND
DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND
DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND
A. Stretch the inner  ex pipe to the required length
A. Stretch the inner ex pipe to the required length
taking into account the additional length needed for
taking into account the additional length needed for
the  nished wall surface. Apply a heavy bead of the
the nished wall surface. Apply a heavy bead of the
high temperature sealant W573-0007 Mill Pac (not
high temperature sealant W573-0007 Mill Pac (not
supplied) to the inner sleeve of the air terminal. Slip
supplied) to the inner sleeve of the air terminal. Slip
the vent pipe a minimum of 2" (50.8mm) over the inner
the vent pipe a minimum of 2" (50.8mm) over the inner
sleeve of the air terminal and secure with 3 #8 screws.
sleeve of the air terminal and secure with 3 #8 screws.
`
`
B. Using the outer rigid pipe, slide over the outer combustion air
B. Using the outer rigid pipe, slide over the outer combustion air
sleeve of the air terminal and secure with 3 #8 screws. Seal
sleeve of the air terminal and secure with 3 #8 screws. Seal
using high temperature sealant W573-0002 (not supplied).
using high temperature sealant W573-0002 (not supplied).
C.
Insert the vent pipes through the  restop maintaining the required clearance to combustibles. Holding the air
C. Insert the vent pipes through the restop maintaining the required clearance to combustibles. Holding the air
terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing
terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing
with caulking (not supplied).
with caulking (not supplied).
D. From inside the house, using silicone, seal between the vent
D. From inside the house, using silicone, seal between the vent
pipe and the  restop. Then slide the black trim collar over the
pipe and the restop. Then slide the black trim collar over the
vent pipe up to the  restop.
vent pipe up to the  restop.
E. If more vent pipe needs to be used to reach the appliance,
E. If more vent pipe needs to be used to reach the appliance,
couple them together as illustrated. The vent system must
couple them together as illustrated. The vent system must
be supported approximately every 3 feet (0.9m) for both
be supported approximately every 3 feet (0.9m) for both
vertical and horizontal runs. Use noncombustible strapping
vertical and horizontal runs. Use noncombustible strapping
to maintain the minimum clearance to combustibles.
to maintain the minimum clearance to combustibles.
The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of its
The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of its
return fl ange.
return fl ange.
W415-1326 / 05.23.14
W415-1326 / 05.23.14
W415-1326 / B / 08.23.18
WARNING
WARNING
WARNING
!
!
!
RETURN FLANGE OF THE MOUNTING PLATE.
RETURN FLANGE OF THE MOUNTING PLATE.
RETURN FLANGE OF THE MOUNTING PLATE.
ELBOWS. KEEP IT PULLED TIGHT.
ELBOWS. KEEP IT PULLED TIGHT.
ELBOWS. KEEP IT PULLED TIGHT.
#8 X 1/2"
#8 X 1/2"
SELF
SELF
DRILLING
DRILLING
SCREWS
SCREWS
HIGH TEMPERATURE
HIGH TEMPERATURE
SEALANT
SEALANT
28.5A
#10x2"
#10x2"
SCREWS
CAULKING
SCREWS
CAULKING
2" (50.8mm) OVERLAP
2" (50.8mm) OVERLAP
HIGH TEMP
SEALANT
#8 X 1/2"SELF DRILLING
#8 X 1/2"SELF DRILLING
SCREWS & WASHERS
SCREWS & WASHERS
HI-TEMP
HI-TEMP
SEALANT
SEALANT
OUTER
OUTER
RIGID PIPE
RIGID PIPE
23.7C
2" (50.8mm)
2" (50.8mm)
OVERLAP
OVERLAP
28.5A
7" (177.8mm) RIGID
7" (177.8mm) RIGID
PIPE
PIPE
HIGH TEMP
SEALANT
INNER COUPLER
INNER COUPLER
OUTER
OUTER
RIGID PIPE
RIGID PIPE
INNER
INNER
FLEX PIPE
FLEX PIPE
23.7C