General Information - Napoleon GDS20N Instructions D'installation Et D'opération

6
6
The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
EN
Installation Code CSA B149.1 in Canada, or the National
EN
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or
ANSI Z223.1 and NFPA 54 in the United States.
As long as the required clearance to combustibles is
maintained, the most desirable and bene cial location
for an appliance is in the center of a building, thereby
allowing the most ef cient use of the heat created. The location of windows, doors and the traf c  ow in the
room where the appliance is to be located should be considered. If possible, you should choose a location
where the vent will pass through the house without cutting a  oor or roof joist.
If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood
 ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.
Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must
be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian
Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.
The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not
The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not
be removed from the cord plug.
be removed from the cord plug.
2.3

GENERAL INFORMATION

2.3 GENERAL INFORMATION
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND
QUALITY!
QUALITY!
Altitude (FT)
Altitude (FT)
Max. Input (BTU/HR)
Max. Input (BTU/HR)
Max. Output (BTU/HR)
Max. Output (BTU/HR)
Efciency (w/ the fan on)
Efficiency (w/ the fan on)
Min. Inlet Gas Supply Pressure
Min. Inlet Gas Supply Pressure
Max. Inlet Gas Supply Pressure
Max. Inlet Gas Supply Pressure
Manifold Pressure (Under Flow Conditions)
Manifold Pressure (Under Flow Conditions)
When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speci c recommendations
When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of specific recommendations
from the local authority having jurisdiction, the certied high altitude input rating shall be reduced at the rate of 4%
from the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4%
for each additional 1,000ft (305mm). Expansion / contraction noises during heating up and cooling down cycles are
for each additional 1,000ft (305mm). Expansion / contraction noises during heating up and cooling down cycles are
normal and to be expected.
normal and to be expected.
Provided that the clearance to combustibles are achieved, the most desirable and benecial location for an
Provided that the clearance to combustibles are achieved, the most desirable and beneficial location for an
appliance is in the centre of a building, thereby allowing the most efcient use of the heat created. The location
appliance is in the centre of a building, thereby allowing the most efficient use of the heat created. The location
of windows, doors and the traf c ow in the room where the appliance is to be located should be considered.
of windows, doors and the traffic flow in the room where the appliance is to be located should be considered.
If possible, you should choose a location where the vent will pass through the house without cutting a  oor or
If possible, you should choose a location where the vent will pass through the house without cutting a floor or
roof joist.
roof joist.
This appliance is approved for closet or recessed installations, as well as for bathroom, bedroom and bed-
This appliance is approved for closet or recessed installations, as well as for bathroom, bedroom and bed-
sitting room installations and is suitable for mobile home installations. The natural gas model can be installed in
sitting room installations and is suitable for mobile home installations. The natural gas model can be installed in
a mobile home that is permanently positioned on its site and fueled with natural gas.
a mobile home that is permanently positioned on its site and fueled with natural gas.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use
with other gases, unless a certied kit is used.
with other gases, unless a certified kit is used.
W415-1326 / 05.23.14
W415-1326 / B / 08.23.18
www.nficertified.org
GDS20
GDS20
NG
NG
0-4,500
0-4,500
20,000
20,000
15,600
15,600
78%
78%
4.5" Water Column (11.2mb)
4.5" Water Column (11.2mb)
7" Water Column (17.4mb)
7" Water Column (17.4mb)
3.5" Water Column (8.7mb)
3.5" Water Column (8.7mb)
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certified in the U.S.
by the National Fireplace
Institute ® (NFI) as NFI Gas
Specialists
4.1B
LP
P
0-4500
0-4500
20,000
20,000
15,600
15,600
78%
78%
11" Water Column (27.4mb)
11" Water Column (27.4mb)
13" Water Column (32mb)
13" Water Column (32mb)
10" Water Column (25mb)
10" Water Column (25mb)