Electronic Device Connections And Functions - Jacuzzi J-300 Manuel D'installation Et Utilisation Et Entretien

External Media Device Playback
The supplied remote control provides no control over external
Auxiliary player operation except for volume control and source
selection. The Auxiliary player performs all external Auxiliary
playback operations.
Power Button: Press once to turn remote "ON" (remote LCD
display will read "No Link"; Press a second time to turn stereo
"ON" (remote LCD display will read "Welcome"); Press a third time
to place the stereo in "Standby" mode.
AUDIO
Audio Button: Allows access to most of the stereo sound
functions. Press continuously to scroll through the following set-
tings (if applicable): Bas-Tre-Bal-Fad-DSP-Area-Loud-DX-Stereo.
MODE
Mode Button: Press continuously to switch between "RA-
DIO, " "USB" and "AUX IN" modes. "BT AUDIO" appears when a Blue-
tooth device is paired with the stereo.
Volume Up Button: Used to increase volume between 0 to
30.
Volume Down Button: Used to decrease volume between
30 to 0.
Play/Pause Button: Press to pause track, press again to
resume playing. (USB Mode)
Mute Button: Press to mute sound, press again to reactivate
sound.
Track Down Button: Press to rewind tracks. (Device Mode
(USB)
Seek Down Button: Seeks down for stations. (Radio Mode)
Track Up Button: Press to move forward tracks. (Device
Mode USB)
Seek Forward Button: Seeks forward for stations. (Radio Mode).
1
Press the button to change music folders. (Device Mode
(USB)
Preset 1: Press to access a preset station. (Radio Mode)
2
Apple Device: Press once to repeat song. Press again to re-
peat entire album. Press again to turn off. Press once to turn on.
AUDIO
MODE
1 2 3
DIR - DIR + REPEAT RANDOM
Press again to turn off. (USB Mode)
Preset 2: Press to access a preset station. (Radio Mode)
3
Press the buttons to change music folders. (Device Mode
USB)
Preset 3: Press to access a preset station (Radio Mode)
Press to play songs in a random order. (Device Mode USB)
Not used (Radio Mode)

Electronic Device Connections and Functions

CAUTION: RISK OF ELECTRICAL SHOCK OR EQUIP-
MENT DAMAGE! Never install, remove or operate any
electrical device (e.g. Apple device/MP3/USB/AUX/Blue-
tooth) while hands are wet or while sitting partially or
fully immersed in the spa!
IMPORTANT: If stereo unit is "ON" (blue light is illuminated on
the stereo power button) then press the power button on the
remote once.
If stereo unit is in "Standby" (red light is illuminated on the stereo
power button) then press the power button on the remote once
to activate the remote (remote LCD display will read "NO LINK").
Press the button again to activate the stereo unit (remote LCD
display will read "WELCOME").
Operating the Radio:
Turn power "ON" to the stereo unit. Press the power button on
the remote.
The LCD screen on the remote will display the following: "Wel-
come, " "Load, " "Radio" and the station number.
You can use the seek button to search for frequencies. You can
save up to 3 stations as presets. Follow the steps below to set a
station:
a. Find a station you want to save.
b. Press and hold one of the three preset buttons. The station
preset number (1, 2 or 3) on the display will quickly flash to con-
firm the setting. To set the additional two stations, conduct this
step again.
Connecting Your Apple Device and MP3 Player Using the USB:
• Locate the USB port in the stereo locker
• Use a 30-pin cable for compatible devices or a cable provid-
ed with your device.
• Connect the USB end of the cable into the USB connection
on stereo.
• Connect the 30-pin end of the cable to the Apple device/
MP3 Player (purchased separately).
• After connecting the cable to both devices, set the player
in the rubber holding base; this means the device is also re-
charged, where applicable.
48