Table des Matières
Publicité
Translation of the German-language operating instructions
Thank you
soldering etc. All STEINEL tools are
for choosing a STEINEL hot air tool.
manufactured to the highest standards
This tool can be used for completing a
and undergo a strict process of quality
wide range of jobs safely and reliably,
control.
such as shrink-fitting, de-soldering,
Safety precautions
!
Read and observe this information
Protect yourself from
before using the tool. Failure to
electric shock.
observe the operating instructions
may result in the tool becoming a
Avoid touching earthed installations
source of danger.
and appliances, such as pipework,
radiators, cookers, refrigerators. Do
When using electric power tools, ob-
not leave the tool unattended while in
serve the following basic safety precau-
operation.
tions to protect yourself from electric
shock, the risk of injury and fire hazards.
Store your tools in
Used carelessly, the tool can start an
a safe place.
unintentional fire or injure persons.
After use set the tool down on its stand-
Check the tool for any damage (mains
ing surface and allow it to cool before
connection lead, housing etc.) before
packing it away.
putting it into operation and do not use
the tool if it is damaged.
When not in use, tools should be stored
in a dry, locked room out of reach of
The tool must not be allowed to
children. This tool is not intended for use
operate unattended.
by persons (adults and children) with
Children should be supervised to make
physical, sensory or mental impairments
sure they do not play with the device.
or lacking experience and/or knowledge
of use unless they are supervised by a
First time of use
person responsible for their safety or
have received instructions from that
A small quantity of smoke may occur
person on how to use the tool.
the first time the tool is used.
Do not overload
your tools.
Take the ambient conditions
into account.
Your work results and safety will be
enhanced if you operate the tool within
Do not expose electric power tools to
the specified output range. After using
rain. Do not use electric power tools
the tool for a prolonged period at max-
when they are damp or in a damp or
imum temperature, you should reduce
wet environment. Exercise care when
the temperature before switching the
using the tool in the proximity of com-
tool off. This will prolong the heating
bustible materials. Do not direct hot air
element's useful life.Do not carry the
onto the same spot for any prolonged
tool by the power cord and do not pull
period. Do not use in the presence of
the power cord to pull the plug out of
an explosive atmosphere. Heat may
the power socket. Protect the power
be conducted to combustible materials
cord from heat, oil and sharp edges.
that are out of sight.
Proper use
The STEINEL HL Stick power tool is intended for shaping plastic as well as for heating shrink tubing. It is also suitable
for soldering, de-soldering and undoing bonded joints. The tool is not intended for use as a hot-air barbecue lighter,
as a hair-drier or for use in vehicles.
Used properly (please refer to the
following safety precautions), the tool
will give you prolonged service and
lasting satisfaction.
Beware of toxic gases
and fire hazards.
Toxic gases may occur when working
on plastics, paints, varnishes or
similar materials.
Beware of fire and ignition hazards.
For your own safety, only use
accessories and attachments that
are specified in the operating instruc-
tions or recommended or specified
by the tool manufacturer. Using
attachments or accessories other
than those recommended in the
operating instructions or catalogue
may result in personal injury.
Repairs must only be
carried out by a qualified
electrician.
This electric power tool complies
with the relevant safety regulations.
Repairs must only be performed by
a qualified electrician, otherwise the
user may run the risk of accidents.
If this tool's main power cord is
damaged, it must be replaced by
the manufacturer or its customer
service department or a similarly
qualified person so as to avoid
hazards.
Keep these safety precautions
with the tool.
- 6 -
Technical specifications
Voltage
230-240 V, 50 Hz
Output
350 W
Temperatures *
1
400 °C without nozzle
500 °C with 7 mm reduction nozzle (included)
Airflow rate
100 l / min. max.
Mains power cord
H05
Protection class
II
Emission sound pressure level
70 dB(A)
Total vibration value
2.5 m/s
2
I K = 0.08 m/s
Weight
0.7 kg
*
1
Temperature profile
Distance from outlet nozzle
20 mm
30 mm
Temperature without nozzle
360 °C
320 °C
Temperature with nozzle
450 °C
350 °C
Tool features
1
Stainless steel outlet nozzle
4
Hanging ring
2
Air inlet keeps out foreign matter
5
Rubber sheathed cord
3
ON/OFF slide switch
6
LED light for illuminating
the work area
For your safety
• The thermal cut-out shuts the tool down if it is overloaded.
• Attaching the reflector nozzle
C D
Tool description - Operation
Operation
3
The tool is switched ON and OFF at the
slide switch. The distance from the object you are working on depends on
material and intended method of working. Always try out temperature on a test piece first. Using the attachable nozzles
(see accessories page on the cover) the flow of hot air can be controlled with maximum precision.
Take care when changing hot nozzles! When using the hot air tool in the self-resting position, make sure it is standing
on a stable, non-slip and clean surface.
2
40 mm
50 mm
100 mm
150 mm
280 °C
230 °C
150 °C
100 °C
290 °C
250 °C
150 °C
100 °C
7
Standing surface
- 7 -
200 mm
75 °C
75 °C
Publicité
Table des Matières
