Description Of The Terminal Blocks - CDVI SASIC Manuel D'installation

INSTALLATION MANUAL
SASIC
Interlocking controller

5.2 Description of the terminal blocks

SAS CARD
Block
1 > 5 screw terminal block: Traffi c light indicator 1 (door 1 = exterior) IN
36 Green light (output)
35 Red light (output)
34 Buzzer (output)
33 0V input voltage
32 Push button (input) > Call or automatic opening
1 > 5 screw terminal block: Traffi c light indicator 1 (door 2 = exterior) OUT
31 Green light (output)
30 Red light (output)
29 Buzzer (output)
28 0V input voltage
27 Push button (input) > Call or automatic opening
2 > 5 screw terminal block: Traffi c light indicator 3 (door 2 = interior) IN
1 Green light (output)
2 Red light (output)
3 Buzzer (output)
4 0V input voltage
5 Push button (input) > Call or automatic opening
2 > 5 screw terminal block: Traffi c light indicator 4 (door 2 = interior) OUT
6 Green light (output)
7 Red light (output)
8 Buzzer (output)
9 0V input voltage
10 Push button (input) > Call or automatic opening
1 > 8 screw terminal block: Exterior Lock A
44 Exterior card reader 1 / door open contact, normally open
43 Alarm (Position)
42 Door status
41 0V input voltage
40 +12V (output)
39 NC (relay contact or +12V if ST2 in 1 and 2)
38 C (common relay)
37 NO (contact relay)
2 > 8 screw terminal block: Interior Lock B
11 Exterior card reader 2 / door open contact, normally open
12 Alarm (Position)
13 Door status
14 0V input voltage
15 +12V (output)
16 NC (relay contact or +12V if ST3 in 1 and 2)
17 C (common relay)
18 NO (contact relay)
3 screw terminal block: RF Aerial (for a remote connection)
1 Aerial +
2 Not used
3 Aerial – coaxial wire shielding
ALARM > 3 screw terminal block: Alarm relay
NO Normally open
C Common
NC Normalement closed
cdvi.com
32
cdvigroup.com
Description
SAS CARD
Block
TAMPER > 3 screw terminal block: Contact normally closed / Alarm on opening)
1 Tamper + (short-cut with 3 if not used)
2 Not used
3 Tamper -
8 screw terminal block : Alarm, Emergency, Locking, Opening
19 Alarm + (contact normally open / Alarm on closing)
20 Alarm -
21 Emergency + (contact normally open / momentary closing triggers alarm and opens)
22 Emergency -
23 Locking + (contact normally open / Locks on closing)
24 Locking -
25 Opening + (contact normally open / Opens the two doors on closing)
26 Opening -
5 screw terminal block: RS485
A A (for the RS485 bus link to control panels and PC interfaces)
B B (for the RS485 bus link to control panels and PC interfaces)
M M (RS485 cable shielding)
- 0V (output voltage 0V for control panels and PC interfaces)
+ 12V (+) (output voltage +12V for control panels and PC interfaces)
12V > 3 screw terminal block: ADC12
+ 12V (+Battery)
- 0V (Input power supply 0V ADC12)
+ + 12V (Input power supply ADC12)
BAT > 3 screw terminal block : Battery 7A – 12V
+ Battery +
Not used
- Battery -
CONTROL PANEL BOARD
5 screw terminal block: RS485
Block
A A (RS485 bus)
B B (RS485 bus)
M M (RS485 cable shielding)
-12V 0V (power supply)
+12V 12V (+) (power supply)
TRAFFIC LIGHT INDICATOR BOARD
5 screw terminal block: Traffi c light indicator*
Block
1 0V input voltage
2 Red light (closed status)
3 Green light (open status)
4 Push button (call or automatic opening)
5 Buzzer
* Refer to traffi c light indicator manual
EN
Description
Description
Description