Sygonix 1925816 Mode D'emploi page 3

Operating Instructions
720P security camera
Item No. 1925816
Intended Use
This surveillance camera is equipped with a motion detector and is capable of low light
recording. The lens has a wide coverage area and the device is compact and unobtrusive.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, fires, electric shocks or other hazards. Read
the instructions carefully and store them in a safe place. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Camera • USB card reader
• USB Cable • Reset pin
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions
carefully and especially
observe the safety information.
If you do not follow the safety
instructions and information on
proper handling in this manual,
we assume no liability for any
resulting personal injury or
damage to property. Such cases
will invalidate the warranty/
guarantee.
a) General Information
• The product is not a toy. Keep it out of the
reach of children and pets.
• Do not leave packaging material lying
around carelessly. This may become
dangerous playing material for children.
• Protect the product from
temperatures, direct sunlight, strong jolts,
high humidity, moisture, flammable gases,
steam and solvents.
• Do not place the product under any
mechanical stress.
• If it is no longer possible to operate the product
safely, take it out of operation and protect it
from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in
poor ambient conditions or
- has been subjected to any serious
transport-related stresses.
• Please handle the product carefully. Jolts,
impacts or a fall even from a low height can
damage the product.
• Consult an expert when in doubt about the
operation, safety or connection of the product.
• Maintenance, modifications and repairs
must only be completed by a technician or
an authorised repair centre.
• If you have questions which remain
unanswered by these operating instructions,
contact our technical support service or
other technical personnel.
• Camera stand
• Operating instructions
b) LiPo Battery
• The rechargeable battery is permanently
built into the product and cannot be
replaced.
• Never damage the rechargeable battery.
Damaging the casing of the rechargeable
battery might cause an explosion or a fire!
Unlike conventional batteries/rechargeable
batteries (e.g. AA or AAA type), the casing
of the LiPo rechargeable battery does not
consist of a thin sheet but rather a sensitive
plastic film only.
• Never short-circuit the contacts of the
rechargeable battery. Do not throw the
battery or the product into fire. There is a
danger of fire and explosion!
• Charge the rechargeable battery regularly,
even if you do are not using the product.
extreme
Due to the rechargeable battery technology
being used, you do not need to discharge
the rechargeable battery first.
• Never charge the rechargeable battery of
the product unattended.
• When charging, place the product on a
surface that is not heat-sensitive. It is normal
that a certain amount of heat is generated
during charging.
c) Connected devices
• Also observe the safety and operating
instructions of any other devices which are
connected to the product.
d) Privacy
• It is the responsibility of the user to be aware of
all applicable laws and regulations that prohibit
or limit the use of cameras, and to comply with
the applicable laws and regulations.
• Recording and circulating an image of an
individual may constitute an infringement of
their privacy for which you may be held liable.
• Ask for authorization
individuals, particularly if you want to keep
your recordings and/or circulate images on
the Internet or any other medium.
• Do not circulate degrading image(s) or one
which could undermine the reputation or
dignity of an individual.
Operating Elements
1 2
7
1 Power / REC
2 Motion detection
recording
3 LED indicators
Getting Started
a) Charge the Battery
• Charge the battery before using for the first time.
• Connect the Micro USB 5 V/DC 1A (5) input to a 5 V USB power adaptor or an available USB
port on your computer using the included cable.
A full charge takes approximately 2 hours. The device may become warm during
charging, this is normal.
LED
Yellow
Yellow
b) Inserting a MicroSD Card
The camera only supports MicroSD cards class 4 to 10, 8 to 32 GB capacity.
Make sure the device is turned OFF. Inserting or removing a card during operation
may damage the card and device.
Inserting the card incorrectly or using excessive force may damage the card and the
card slot.
c) Formatting a MicroSD Card
Formatting will erase all data on the MicroSD card. Make sure you save any
important information before formatting.
• Insert the card into the Micro-SD card slot (4) then connect to an available USB port on your
computer. Format the card using the FAT32 file system. Refer to your computer operating
instructions for information about how to do this.
d) Camera Settings
To access camera settings, a MicroSD card must be inserted before connecting the
device to your computer.
• Connect the camera to your computer using the included USB cable.
• Turn the device on by pressing and holding the
2 seconds.
• LED indicators (3): Blue flashes 1x then turns off. Red flashes 3x and stays on.
• The device will appear as a removable disk on your computer.
• Select the removable disk then double click "SetCamera.exe".
• Change any options on the settings menu and select "SAVE" to keep any new settings.
Description of Settings
Setting
Language
Time Watermark
(yes/no)
Date Format
Date
Time
Light Frequency
(Hz)
before filming
Image Quality
Overwrite (On/Off)
Audio (On/Off)
3 4 5
4 Micro-SD card slot
5 Micro USB 5 V/DC 1A
input
6 Reset hole
Status Description
ON Battery charging
OFF Charging complete
• Insert a MicroSD card into the Micro-SD
card slot (4) with the contacts facing up as
shown.
• Carefully push the card all the way in using
the tip of your finger. You will feel a "click"
when the card is in position.
• To remove, gently push until you feel a
"click", then release to eject.
Power / REC (1) button for approximately
Description
Select interface language.
Select "Yes" if you would like to imprint the video with time and date.
"YY/MM/DD", "DD/MM/YY", or "MM/DD/YY".
Set current date.
Set current time.
If you notice any screen flicker during video playback, try switching to
a different frequency.
Select a recording quality VGA, 720P, 1080 P
A higher recording quality requires more memory space.
On: When the MicroSD card gets full, old recordings will be overwritten.
Off When the MicroSD card gets full, recording will stop.
Select "On" to record a video with sound and "Off" for no sound.
6
8
9
7 Camera
8 Magnetic platform
9 Adhesive base