Preliminary Operations Before; Using The Machine - ST. SpA F 72FL Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

–    t he transmission is in "neutral";
–    a ll the cutting means are disengaged;
–    t he operator is seated.
b) The engine stops when:
–    t he operator leaves his seat;
–    t he grass catcher is lifted when the cutting 
means are engaged;
–    t he parking brake is engaged without disen-
gaging the cutting means;
–    t he cutting means is engaged without the 
grass catcher in place;
–    t he parking brake is engaged without disen-
gaging the cutting means.
–    t he speed change is activated (see 4.22)  with 
the parking brake on.

5.3 PRELIMINARY OPERATIONS BEFORE

STARTING WORK
Before starting to mow, it is necessary to carry 
out several checks and operations to ensure 
you can work efficiently and in maximum safety.
5.3.1 Seat adjustment (Fig. 5.1)
To change the seat position, loosen the four fix-
ing bolts (1) and slide it along the slots.
Once you have found the right position, tighten 
the four screws (1) thoroughly.
5.3.2 Tyre pressure (Fig. 5.2)
Having the right tyre pressure is the main condi-
tion for ensuring that the cutting-means assem-
bly is horizontal and mows evenly.
Unscrew the valve caps and connect a com-
pressed air line with a gauge to the valves and 
adjust the pressure to the indicated values.
5.3.3 Filling with oil and fuel
NOTE The type of oil and fuel to use is given
in the engine manual
To reach the oil dipstick,  turn the seat over and 
open the cover underneath.
With the engine off, check the oil level. Accord-
ing to the instructions in the engine manual, this 
must be between the MIN and MAX marks on 
the dipstick. Fig. 5.3)
Refuel using a funnel, but do not completely fill 
the tank. Fig. 5.4)
DANGER!
Refuelling should be carried
out in an open or well-ventilated area with
engine stopped. Always remember that pet-
rol fumes are inflammable. DO NOT TAKE A
NAKED FLAME TO THE TANK'S OPENING
IN ORDER TO SEE THE TANK'S CONTENTS
AND DO NOT SMOKE WHEN REFUELLING.
IMPORTANT Do not drip petrol onto the plas-
tic parts to avoid ruining them. In the event of ac-
cidental leaks, rinse immediately with water. The
warranty does not cover for damage to plastic
parts of the bodywork or the engine caused by
petrol.
5.3.4 Fitting the guard at the exit
(grass catcher)
WARNING!
out having fitted the exit guard!
Lift the mobile cover (1) and hook on the grass 
catcher inserting the two joint pins (2) in the 
holes on the two supports  (3) Fig. 5.5).
5.3.5 Checking machine safety
and efficiency
1.    C heck that the safety devices function as de-
scribed (see 5.2).
2.    C heck that the brake is in perfect working 
order.
3.    D o not start mowing if the cutting means 
vibrate or if you are unsure whether they are 
sharp enough. Always remember that:
      –     A  badly sharpened cutting means pulls at 
the grass and causes the lawn to turn yel-
low.
      –     A  loose cutting means causes abnormal 
vibrations and can be dangerous.
WARNING!
you are unsure whether it is working safely
or efficiently. If in doubt, contact your Dealer
immediately to make the necessary checks
or repairs.

5.4 USING THE MACHINE

5.4.1 Ignition
To start the engine (Fig. 5.7):
–  open the fuel stopcock (1) (if fitted) accessing 
it from the left rear wheel compartment;
–    p ut the transmission into neutral («N»)
(see 4.22);
–    d isengage the cutting means (see 4.6);
–    a pply the parking brake on sloping ground;
–    f or a cold start, use the choke (see 4.2);
–    i f the engine is already warm, just put the lever 
between «SLOW» and «FAST»;
–    i nsert the ignition key and turn to «ON» to 
make electrical contact, then turn to «START» 
to start the engine;
–    r elease the ignition key once the engine has 
started.
9
Never use the machine with-
Do not use the machine if

Publicité

Table des Matières
loading

Table des Matières