Accessories - Silverline 942944 Mode D'emploi

942944
Before Use
WARNING: Always disconnect from the air supply and depressurise
before cleaning or carrying out any maintenance.
WARNING: Before fitting sanding sheets, ensure the sander is disconnected
from the power supply.
Note: DO NOT continue to use worn, torn, or heavily clogged sanding
sheets. Ensure foreign objects, such as nails and screws, are removed from
the workpiece before commencing sanding.
WARNING: DO NOT use a sanding sheet on wood that has previously been
used on metal. This may cause scouring on the wooden surface. DO NOT
use this sander for sanding magnesium.
Note: Before every use drip 3 droplets of Air Tool Oil into the Air Inlet (9) to
increase tool longevity.
Fitting the quick connector
Note: This tool is supplied with two different male air line quick connectors:
EQ-4
commonly used
in Europe
• Please choose the connector that is compatible with the air line system
you are using, and install as outlined below:
1. Apply some PTFE tape (not included) to the screw threads of the Quick
Connector (10). This will help to maintain an air-tight seal
Note: Apply PTFE tape tightly, and in a clockwise direction, so it does not
come off when the thread is screwed into the tool.
2. Remove the protective plug from the Air Inlet (9)
3. Using a spanner (not included) screw the Quick Connector into the Air
Inlet located at the base of the handle
4. Connect to the air line, pressurise carefully, and carry out a leak check
(eg by spraying small amounts of soapy water on to the outside of the
connectors)
• Air lines fitted with matching female quick connectors will now be a
push-fit to the tool
Air supply connection
QUICK COUPLER
TO YOUR NIPPLE
AIR TOOL
RECOIL HOSE
LEADER HOSE
• This tool should be connected to a clean, dry air supply with inline oiler
and water separator
• Do not allow supply pressure to exceed the maximum stated
(see "Specifications")
• Ensure that water is drained from air system daily
• Ensure that all parts of the system (hoses, couplers, etc.) are correctly
rated for the air pressure to be used
Fitting a sanding belt
1. Depress the Tensioning Lever (4) and push the Tensioning Arm (1) into
the Extension Arm (5), then release the Tensioning Lever
2. Wrap the Sanding Belt (3) around the Drive Pulley (12) and the
Tensioning Pulley (2), ensuring it is centred
3. Tension the Sanding Belt by pressing and holding the Tensioning Lever.
Release the Tensioning Lever once the belt is installed
EN-6
mainly used
in the UK
WATER SEPARATION
NIPPLE
OILER
DRAIN DAILY
REGULATOR AIR SUPPLY
Angle adjustment
• The Extension Arm (5) is adjustable to increase versatility when
performing sanding operations to complex geometries
1. Loosen the Angle Adjustment Screw (6) using the provided Hex Key, and
rotate the entire sanding belt assembly to the desired position
2. Securely fasten the Angle Adjustment Screw
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and
hearing protection, as well as suitable gloves, when working with this tool.
Note: Always use clamps to secure the workpiece to the workbench
wherever possible.
1. Connect the sander to the air supply and ensure the pressure setting is
correct, see 'Specifications' for the air supply pressure rating
2. Hold the tool by the Handle (7), and gently squeeze the Throttle Trigger
(11) towards the Handle
3. The Sanding Belt (3) will begin to rotate. Squeeze the Throttle Trigger
further to increase the speed, slightly release to decrease the speed,
4. With the Sanding Belt spinning at the required speed, slowly move the
belt towards the workpiece and gently engage the material
5. Apply moderate pressure to the workpiece surface during operation. Do
not apply excessive pressure
• To stop the tool, move the Sanding Belt away from the workpiece, fully
release the Throttle Trigger and allow the Safety Catch to re-engage

Accessories

• A range of accessories and consumables, including Coiled Air Hose
(269591), Air Filter Regulator & Lubricator (245014) and Mini In-Line
Oiler (456965) is available from your Silverline stockist. Spare parts can
be obtained from toolsparesonline.com
Maintenance
General inspection
• Regularly check that all the fixing screws are tight
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine's service life. Clean the body
of your machine with a soft brush, or dry cloth. If available, use clean,
dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do
not use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable
spray lubricant
Storage
• Store this tool carefully in a secure, dry place out of the reach of
children
www.silverlinetools.com
Air Belt Sander
7