Publicité
Les langues disponibles
Les langues disponibles
B
A
1
2
3
CLIK!
Panic (red LED)
Adjusting the ring
Brightness
Saturation colour
Standard functions
- Disabling the ring with light signal (the video
handset is still activated with all its functions), in the
OPHERA model only.
- Door open warning light.
- Warning that porter switchboard is trying to get in
touch.
- Doorbell input.
- Possibility to route the call from 3 externally loca-
ted buttons to one video intercom.
- Distinctive ringing depending on where the call is
made from (entry panel, doorbell, porter switch-
board, intercom unit).
- Call note type can be programmed to distinguish
between a call made from the entry panel (4 melo-
16
dies) and the doorbell (4 melodies).
- Number of rings announcing the call can be pro-
grammed from the entry panel (the doorbell note is
not programmable).
- Call can be rerouted to another receiver.
If the user called does not answer, the call can be
rerouted to another receiver by programming with
MPP/300LR or PCS/300.
- Adjusting the volume of the ring to 3 levels.
Hands-free operation
When a call is made from the entry panel, press the
button to initiate communication, the LED light.
To end communication, press the button
the LED goes off.
If you wish to interrupt a communication temporarily
during a conversation, press the button
the OPHERA/B model), the LED flashes.
To restore communication press
OPHERA/B model), the LED goes off.
Talk-listen operation
When a call is made from the entry panel, press the
button to initiate communication, the LED light.
Press down the button
model) to speak with the entry panel.
Release the button
model) to listen,the LED light.
To end communication, press the button
LED goes off.
Entry panel selection in installations with a num-
ber of entry panels
With the system off, turn on the monitor by pressing
the entry panel activation button
switch between entry panels.
Alarm
The alarm is sent each time any remote device con-
nected to the AL input of the M1 terminal block is
activated.
This warning takes priority over all the others.
The command is handled through the actual porter
switchboard (the message Alarm and the user's
number come up on the display).
Privacy (in the OPHERA/B model only)
17
This function is active only with the video handset
station off.
The user can press the Mute/Privacy
isolate the receiver from all calls sent to it, the LED
light.
When making a call to the receiver, the porter recei-
ves the Privacy status warning.
Press the same button again to exit Privacy status,
the LED goes off.
Porter call
By pressing the Porter call button
OPHERA model where installed) a call is made by
the user to the porter switchboard.
Should the porter call the user and the user fail to
answer, the LED on the receiver comes on if the
porter leaves a message.
Once the user manages to speak with the porter,
the LED goes off.
Panic (in the OPHERA/B model only)
By pressing the Panic button
sent to the porter switchboard (the message Panic
18
and the user's number come up on the display).
The red LED comes on to confirm receipt by the
porter.
This LED goes off when the porter calls the user.
This warning takes priority over all the others.
Calibrating the audio levels
- Activate the receivers
listen operating mode.
- Adjust the volumes on the entry panel in the talk-
listen mode.
- Go to the hands-free mode
OPHERA/B model) and check the regularity of swit-
ching from one channel to another.
- If there is difficulty in getting the line in one of the
two directions, increase the volume slightly in the
direction where you have difficulty and reduce it in
the other direction.
In combined systems (receivers and hands-free)
we recommend you first adjust the communication
levels for the hands-free system.
If necessary, adjust the volumes on the entry panel
to achieve a better compromise.
Function of jumper SW1
(Resistive load termination)
The unit features a jumper SW1 (fig. 8) for the imped-
ance terminating the signal line. Remove the jumper
if the line continues towards other video handsets.
Function of jumper SW2
(Selects power source)
The video handset has a jumper SW2 (fig. 8) for
selecting the type of power supply (from BUS or a
separate power supply unit).
For power supply from X1 BUS (max. 1 video hand-
again,
set active only), position jumper SW2 on BUS
(default setting).
For separate power supply, position jumper SW2 on
(
in
LOCAL (as additional receiver for a simultaneous
call or use in X2 installations).
(
in the
OPHERA AND OPHERA/B HANDS-FREE
INTERCOMMUNICATING COLOUR
VIDEO HANDSET
The button accessory provided lets the video hand-
set change to an intercommunicating appliance.
(
in the OPHERA/B
It features the following controls (fig. 4):
1÷4(5÷8) Call buttons
(
in the OPHERA/B
, the
To apply the button accessory, remove the left
cover and unscrew the two screws (fig. 5).
Insert the intercommunicating accessory, tighten
the two screws and insert the cover (fig. 6-7).
. Press again to
This accessory allows the basic functions for the
video handset to be used:
- Intercom calls (max. 8) with VSE/301 selector or
for activating auxiliary services with actuators.
- Call transfer in intercom mode.
- Light signal with doubling LED to indicate system
busy.
If there is a call from the entry panel during a con-
versation between intercom sets, a short audible
signal repeated every 5 s advises the receiver's
user of the call.
By pressing one of the call buttons and pressing
receiver.
The receiver receiving the transferred call can, in
button to
turn, transfer the call.
STANDARD PROGRAMMING
(without using relevant programmers)
To programme the call in system 300 or X1 (X2)
installations, see the literature enclosed with the
XA/300LR control unit and X2 entry panel.
To program call buttons 2 and 3, where necessary,
simply press the corresponding keys following the
(
in the
first call button once you have entered receiver pro-
gramming mode.
NOTE. Do not exit receiver programming mode until
you have associated all the desired calls.
To programme intercom calls, see the instructions
provided with the VSE/301 selector.
PROGRAMMING WITH MPP/300LR
OR PCS/300
The unit can be programmed through the
the panic status is
MPP/300LR unit using the dedicated profile for the
XC/310 receiver, or by means of PCS/300 by selec-
ting the corresponding receiver (OPHERA).
and select the talk-
Doubling button (for calls 5÷8)
(red LED)
, the conversation can be transferred to another
(
in the
5
Publicité
