Specifications; Interface - Sony UP-D890 Mode D'emploi

Specifications

Printer
Thermal head
Thin-film thermal head (with built-in drive IC)
1024-dot drive
Gradation
256 (8 bit)
Memory capacity
Standard 1 Mbyte memory:
1024 × 1024 × 8 bit
4Mbyte 72-pin SIMM installed:
5120 × 1024 × 8 bit
Print size
Standard 1 Mbyte memory:
Max. 100.3 × 100.3 mm
4Mbyte 72-pin SIMM installed:
Max. 501.5 × 100.3 mm
Printing speed
About 5.5 seconds/screen
Picture elements
Standard 1 Mbyte memory:
Max. 1024 × 1024 dots
4Mbyte 72-pin SIMM installed:
Max. 5120 × 1024 dots
Dots density
H: 100.3/1024 = 0.098
V: 100.3/1024 = 0.098
Square dots
Power requirements
120 V AC, 50/60 Hz
220 to 240 V AC, 50/60 Hz,
Power consumption
120 V: 1.5A
220 to 240 V: 0.8A
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
20 % to 80 %
Storage/transportation temperature
–20 °C to 60 °C (–4 °F to 140 °F)
Storage/transportation himidity
20 % to 90 %
Dimensions
Approx. 154 × 106.5 × 303.5 mm (w/h/d) (6
× 12 inches)
1
4 ⁄
4
Mass
Approx. 3.6 kg (7 lb 11 oz), Printer only
Protection against electric shock
Class I
Protection against harmful ingress of water
Ordinary
Degree of safety in the presence of flammable
anesthetics or oxygen
Not suitable for use in the presence of flammable
anesthetics or oxygen
Mode of operation
Continuous
Supplied accessories

Interface

Control connector
Data transmission system
Logic level
Parallel Interface connector pin assignment
H
® ®
V
® ®
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
×
1
⁄
16–17
8
18
19–30
31
32
33
34
35
36
ECP modes of the two-way parallel interface standard
(IEEE STD 1284-1994).
Design and specifications are subject to change without
notice.
Paper roll (UPP-110HA) (1)
AC power cord (1)
Operating Instructions (1)
Head cleaning sheet (1)
Printer driver disk (1)
Registration card* (English only, 1)
Software license agreement*
(English only, 1)
Clamp filter (1)
* Valid in the U.S.A. and Japan only
IEEE 1284-B connector (amphenol 36-pin)
Input: Max. 5 V (TTL)
Output: Max. 5 V (TTL)
8 bit, parallel,
IEEE STD 1284-1994 (Compatible, Reverse
Nibble and ECP modes)
TTL
Pin No. I/O Signal
Interface mode
Compatible Nibble
I nStrobe HostClk
I/O Data1 (LSB)
I/O Data2
I/O Data3
I/O Data4
I/O Data5
I/O Data6
I/O Data7
I/O Data8 (MSB)
O nACK PtrClk
O Busy PtrBusy
O PError AckDataReq nAckReverse
O Select Xflag
I nAutoFd HostBusy
Not defined
GND
O Peripheral Logic High (pull up to +5 V at 1 kilohm)
GND
I nInit nInit
O nFault nDataAvail
Not defined
Not defined
Not defined
I nSelectIn IEEE 1284 Active IEEE 1284 Active
UP-D890 supports Compatible, Reverse Nibble, and
ECP
HostClk
PeriphClk
PeriphAck
Xflag
HostAck
nReverseRequest
nPeriphRequest
35
Others