Ryobi RBC430SESD Manuel D'utilisation page 24

WARNING
Be certain all knobs and fasteners are fully tightened
before operating the equipment. Periodically check for
tightness during use to avoid serious injury.
REMOVING THE REELEASY™ STRING HEAD
■ Stop the engine.
■ Open the ReelEasy™ String Head by depressing the
latches on each side. The contents of the string head
are spring loaded, so keep your other hand over the
string head cover while depressing the latches.
■ Remove the string head cover, bump knob, line, spool,
and spring.
■ Place the holding pin through the hole in the upper
flange washer and the hole in the gear head. Using the
bump knob, to turn the hex bolt clockwise to remove.
■ Remove the string head housing from the drive
connector.
■ Using a combination wrench, turn the drive connector
clockwise to remove.
■ Remove the upper flange washer from the gear shaft
and retain for later use.
■ Use the combination wrench supplied to loosen guard
screw, then remove grass deflector from the blade
guard.
NOTE: Store the disassembled parts together for later
use.
INSTALLING THE TRI-ARC™ BLADE
See fi gure 6a.
To reduce the risk of injury, keep the blade protector on
the blade at all times. Remove the blade protector only
during cutting operations.
■ Place the upper flange washer over the gear shaft with
the hollow side towards the blade guard.
■ Centre the blade on the upper flange washer and make
sure the blade sits flat. Install the cupped washer with
the raised centre away from the blade and make sure
it sits well into the gear shaft.
■ Install the blade retainer nut until finger tight.
■ Place the holding pin through the hole in the upper
flange washer and the hole in the gear head. Using
the combination wrench turn the blade retainer nut
counterclockwise half a turn from finger tight
CONVERTING FROM BRUSHCUTTER (TRI-ARC™
BLADE) TO STRING TIMMER
See fi gure 6b.
When using the string head, the blade guard must be
attached with the grass defl ector.
English (Original instructions)
To reduce the risk of serious personal injury, always
stop the engine before making any adjustments such
as changing cutting heads.
Be certain all knobs and fasteners are fully tightened
before operating the equipment. Periodically check for
tightness during use to avoid serious injury.
REMOVING THE TRI-ARC™ BLADE
■ Stop the engine.
■ Place the holding pin through the hole in the upper
■ Remove the cupped washer and blade.
■ Remove the upper flange washer from the gear shaft
INSTALLING THE REELEASY™ STRING HEAD
■ Install the upper flange washer onto the gear shaft with
■ Install the drive connector into the gear shaft. Place the
■ Place the string head housing on the drive connector.
■ Place the holding pin through the hole in the upper
■ Install the spring into the string head housing and push
■ Reinstall the spool. For the straight shaft attachment
■ Replace the bump knob by inserting it into the centre
■ Replace the string head cover, aligning latches with
■ Attach the grass deflector to the blade guard and align
22
WARNING
WARNING
flange washer and the hole in the gear head. Using
the combination wrench, turn the blade retainer nut
clockwise to remove.
and retain for the later use.
the hollow side towards the gear head.
holding pin through the hole in the upper flange washer
and the hole in the gear head. Using the combination
wrench, turn the drive connector counterclockwise,
and tighten securely.
Make sure the housing is fully seated.
flange washer and the hole in the gear head. Place
the hex bolt into the drive connector. Using the bump
knob, to turn the hex bolt counterclockwise, and
tighten securely.
down to seat.
with the ReelEasy™ string head, the spool should be
placed so "This side out for straight shaft" is visible on
the spool.
of the spool.
openings in the string head. Press cover and string
head together until both latches snap into openings
securely.
the 3 screws on the grass defector to the screw holes
on the blade guard.
NOTE: Store the disassembled parts together for later