Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Work Area Precautions
1.
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power
tool. Distractions can cause you to lose control. Protect others in the work area
from debris such as chips and sparks. Provide barriers or shields as needed.
Electrical Safety
1.
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove
the grounding prong or modify the plug in any way. Do not use any
adapter plugs. Check with a qualified electrician if you are in doubt
whether the outlet is properly grounded. If the tool should electrically
malfunction or break down, grounding provides a low resistance path to carry
electricity away from the user.
2,
Double insulated tools are equipped with a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double insulation eliminates the need for
the three wire grounded power cord and grounded power supply system.
3.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
4.
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
5.
Do not abuse the Power Cord. Never use the Power Cord to carry the
tool or pull the Plug from an outlet. Keep the Power Cord away from
heat, oil, sharp edges, or moving parts. Replace damaged Power Cords
immediately. Damaged Power Cords increase the risk of electric shock.
6.
When operating a power tool outside, sue an outdoor extension cord
marker "W-A" or "W". These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
Personal Safety
1.
Stay alert. Watch what you are doing, and use common sense when
operating a power tool. Do not use a power tool while tired or under
the influence of drugs, alcohol, or medication. A moment of inattention
24
EN
Rev. 02.03.2017
while operating power tools may result in serious personal injury.
2.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
3.
Avoid accidental staring. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
4.
Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
5.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
6.
Use safety equipment. Always wear eye protection. Dust mask, nonskid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
Tool Use and Care
1.
1. Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work piece by hand ro against
your body is unstable and may lead to loss of control.
2.
Do not force the tool. Use the correct tool for your application. The
correct tool will do the job better and safer at the rate for which it is designed.
3.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
4.
Disconnect the Power Cord Plug from the power source before making
any adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
5.
Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
6.
Maintain tools with care. Keep cutting tools maintained and clean.
Properly maintained tools are less likely to bind and are easier to control. Do not
use a damaged tool. Tag damaged tools "Do not use" until repaired
7.
Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tool's operation. If damaged,
have the tool serviced before using. Many accidents are caused by poorly
maintained tools.
8.
Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
Rev. 02.03.2017
EN
25
Publicité
Table des Matières
