Before Starting The Equipment; Montage; Operation - Scheppach GS50 Traduction Des Instructions D'origine

7. Before starting the equipment

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
m Warning!
Always pull the power plug before making ad-
justments to the equipment.

8. Montage

n IMPORTANT!
You must fully assemble the appliance before
using it for the first time!
1. Open the box and remove the machine and all of
its accessories.
2. Mounting the support feet (Fig. 3)
- First rotate the frame (5) (Fig. 2).
- Fit the two support feet (7) as shown in the Fig.
3. Mounting the idlers (Fig. 4)
- Mount both idlers (Pos. 8).
4. Installing upper section of machine on frame
(Fig. 5)
- Place upper section of machine (12) the other
way round with the loading slot (1) on the ground
(Fig. 5).
- Place the frame (5) on the upper section of the
machine (Fig. 5).
- Screw both components with the six fillister-
head Phillips screws in the correct holes (Fig. 5).
5. Installing drip tray (Fig. 6)
- Place the locking mechanism (3) on the drip tray
(6) in its lowest position (Fig. 6).
- Push the drip tray fully into the frame (Fig. 6).
- Press the locking mechanism (3) on the drip tray
(6) back into its highest position (Fig. 6).

9. Operation

m WARNING!
The shredder can only be started if the collection
box (6) has been pushed into the frame (5) and
the locking device (3) is in the upper position.
Control panel (Fig. 1)
• Manual change of rotational cylinder direction:
(8)
- Button „▲" - anti-clockwise: When this button
is pressed, the blade cylinder rotates anti-
clockwise. This is necessary when jammed
shredding material needs to be freed. This
function is only available when the shredder is in
operation.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
- Button „▲" - clockwise: This button switches
the direction of the blade cylinder from anti-
clockwise back to clockwise.
Once the material is clamped in position, first press
the red switch to stop the device. Press the reverse
switch then the green switch to restart the device. Re-
move the jammed material. Press the red switch to
stop the device again, then press the forward switch.
Then you can continue to work.
• On switch (9): Pressing this button starts the
shredder and the blade cylinder rotates clockwise.
• Off switch (9): Pressing this button stops the
shredder.
Working with the shredder
Alternating with branches, shred withered gar-
den waste and branches that have been stored
several days to prevent the shredder from be-
coming blocked.
• Make sure the collection box (6) is pushed into the
frame (5) correctly and the locking device (3) is in
the upper position.
• Connect the shredder to the power supply.
• Turn the shredder on by using the on switch (9).
• Fill shredding material into the feed hopper and it
will be drawn in.
• Caution: If the shredding material becomes
jammed, use the switch to change the rotational di-
rection of the cylinder (10) so it runs anti-clockwise.
• Make sure the shredder has completely shred-
ded the input material before adding new.
• Do not use your hands to push in more shredding
material. Use the special pushing device or other
shredding material.
• When you have finished working with the shredder,
turn it off and disconnect it from the mains.
Emptying the collection box
• Stop the shredder using the off button (9).
• Set the locking device (3) to the lowest position.
• Pull out the collection box (6) and empty it.
• Re-insert the collection box (6) and push the lock-
ing device (3) up again.
Setting the counter blade
The counter blade and the blade cylinder have
been ideally adjusted by the manufacturer. Re-
adjusting the counter blade is only required if it
becomes worn. For maximum performance, it is
necessary that the distance between the counter
blade and blade cylinder is about 0.50 mm.
• Turn the shredder on.
• Turn the adjustment wheel (4) clockwise until you
can hear slight grinding sounds.