• Clean the device regularly with a damp cloth and
some soft soap. Do not use any detergents or sol-
vents; these might attack the plastic parts of the
device. Make sure that no water can get into the
interior of the device.
• Oil the moving parts once a month in order to ex-
tend the tool life. Do not oil the motor.
Carbon brushes
If excessive sparks are generated, have an electri-
cian check the carbon brushes. Attention! The car-
bon brushes must only be replaced by an electrician.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brush, saw blade, batteries, ta-
ble inserts, push stick, push handle, V-belt
* Not necessarily included in the scope of delivery!
14. Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.
15. Electrical Connection
The installed electric motor is connected ready for
operation. The connection complies with the relevant
VDE and DIN regulations. The customer's network
connection and any extension cable used must com-
ply with these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection condi-
tions. This means that its use at freely selectable
connection points is not permitted.
• If the network conditions are unfavourable, the de-
vice may result in temporary voltage luctuations.
• The product is intended for use only on premises
which have a mains continuous current rating of at
least 100 A per phase and are supplied by a distri-
bution network with a rated voltage of 230V.
• As the user, you must ensure – in consultation with
your electricity supply company if necessary – that
the continuous current carrying capacity of the net-
work at the connection point to the public mains is
suficient for the connection of the product.
36 | GB
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
Important Instructions
If the motor is overloaded, it switches itself off auto-
matically. After cooling down (times vary), the motor
can be switched on again.
Faulty Electrical Connection Cable
Insulation damage often occurs to electrical connec-
tion cables.
The causes of this may be as follows:
• Pressure points if connection cables are routed
through windows or door gaps.
• Kinks caused by improper attachment or routing of
the connection cable.
• Cut surfaces caused by vehicles driving over the
connection cable.
• Insulation damage caused by tearing out of the wall
socket.
• Cracks resulting from the insulation becoming old.
Such faulty electrical connections must not be used
and may endanger life due to the damage to the in-
sulation.
Electrical connection cables should be checked reg-
ularly for damage. Ensure that during such checks,
the connection cable is not connected to the mains.
Electrical connection cables must comply with the
relevant VDE and DIN regulations. Only use connec-
tion cables with the marking H05VV-F.
It is stipulated by law that the type of connection cable
must be printed on it.
Alternating Current Motor
The mains voltage must be 230 V~.
Extension cables up to 25 m in length must have a
cross-section of 1.5 mm².
Connections and repairs to the electrical equipment
may only be performed by a qualiied electrician.
If you have any queries, please provide the following
information:
• Current type of the engine
• Data from the machine type plate
• Data from the motor type plate
16. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit.
The raw materials in this packaging can be reused
or recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Do not throw batteries away with house-
hold waste, or throw them into fire or water. Batteries
should be collected and recycled or disposed of in
an environmentally friendly manner. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council!