Use - Scheppach HS250L Traduction Des Instructions D'origine

Transverse stop (Fig. 29)
• When the wood is being cut to size, the transverse
stop (31) must be extended with the stop rail (30) of
the parallel stop (14).
• Push the transverse stop (31) into a groove (28) of
the saw table.
• Loosen the knurled screw (29).
• Turn the transverse stop (31) until the desired angle
is set. The notch on the guide bar shows the angle
that has been set.
• Retighten the knurled screw (29).
• To extend the lateral end stop (31) with the end stop
rail (30), the end stop rail (30) must be removed
from the parallel end stop (14). Now the stop rail
has to be mounted as shown in Figure 29; use the
knurled nuts (m) for this purpose.
Caution!
• Do not push the stop rail (30) too far in the direction
of the saw blade.
• The distance between the stop rail (30) and saw
blade (4) should be approximately 2 cm.
Adjusting the scale of the parallel stop (Fig. 30)
• Check whether the display on the sight glass (p) of
the parallel stop (14) shows the correct values with
respect to the cutting line. If this is not the case,
please proceed as follows:
• Release the screw (q) with which the display on the
sight glass (p) of the parallel stop (14) is attached.
The sight glass (p) display can now be set to the
correct position.
• Now, retighten screw (q) on the sight glass (p).
Adjusting the Laser (Figure 32)
If the laser (32) no longer shows the correct cutting
line, this can be readjusted. To do this, open the
screws (z). Adjust the laser so that the laser beam
hits the cutting teeth of the saw blade (4).Tighten the
screws (z) again.
Using the Laser
• The laser (32) enables you to carry out precision
cuts with your circular saw.
• The laser light is produced by a laser diode sup-
plied by two batteries. The laser light is expanded
to form a line and is emitted through the laser exit
aperture. You can then use the line as an optical
marking for the cutting line of the precision cut.
Please note the laser safety information.
• Switch on the laser: turn the laser on/off switch (33)
to I. When the saw blade guard (2) is mounted, the
laser on/off switch (33) is accessible through a re-
cess in the guard (Figure 31). A red laser beam is
now projected out of the laser exit aperture. If you
guide the laser beam along the cutting line mark
while sawing, you will achieve clean cuts.
34 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Switch the laser off: turn the laser on/off switch (33)
to 0. The laser beam goes off. Please always turn
the laser off when it is not required in order to save
the batteries.
• The laser beam may be blocked by dust deposits
and chips. You should therefore remove these par-
ticles from the laser exit aperture after every use
(with the device switched off).

11. Use

m Working Instructions
After each new adjustment, we recommend a trial cut
in order to check the set dimensions. After the saw
has been switched on, wait until the saw blade has
reached its maximum speed before you carry out the
cut.
Secure long workpieces against tilting at the end of
the cutting process (e.g. unwinding stand etc.)
Caution with incision cutting.
Operate the device only with a suction system. Check
and clean the suction channels regularly.
Suitability of the saw blades:
24 teeth: soft materials, high chip removal, rough cut
image
48 teeth (not included in the scope of delivery): hard
materials, lower chip removal, iner cut image
Performing Longitudinal Cuts (Fig. 33)
Here, a workpiece is cut in its longitudinal direction.
One edge of the workpiece is pressed against the
parallel stop (14) while the lat side lies on the saw
table (1).
The saw blade guard (2) must always be lowered onto
the workpiece.
The working position during longitudinal cutting must
never be in a straight line with the cutting line.
• Adjust the parallel stop (14) according to the work-
piece height and the desired width.
• Switch on the saw
• Place your hands with the ingers closed together
lat on the workpiece and push the workpiece along
the parallel stop (14) into the saw blade (4).
• Guide from the side with your left or right hand (de-
pending on the position of the parallel stop) only up
to the front edge of the saw blade guard (2).
• Always push the workpiece through to the end of
the riving knife (3).
• The cutting waste remains on the saw table (1) until
the saw blade (4) is back in its resting position.
• Secure long workpieces against tilting at the end
of the cutting process! (e.g. unwinding stand etc.)