Scope Of Delivery (Fig. 3); Proper Use - Scheppach BASA3 Traduction Des Instructions D'origine

3. Scope of delivery (Fig. 3)

• Band saw
• Parallel stop (6)
• Guide rail (7)
• Hand wheel for cutting speed (9)
• Transport handle (10)
• 1x Travel fixture (11)
• Saw table (24)
• 2x mounting plates for handle (29)
• Transverse cutting gauge (30)
• 4x wing screws (35)
• 4x frame legs (36)
• 1x intermediate plate (37)
• 4x wing screw washers (38)
• 2x swivel part screws (M6 x 12) (39)
• 2x swivel part washers (40)
• 1x swivel part fixing screw (41)
• 1x Locking nut for handwheel for cutting speed (42)
• 1x Washer handwheel for cutting speed (43)
• 24x screws for machine stand and mounting plates
(M6 x 12) (44)
• 24x nuts for machine stand and mounting plates
(M6) (45)
• 24x washers for machine stand and mounting plates
(46)
• 4x screws for travel fixture (M8 x 16) (47)
• 4x nut for travel fixture (48)
• 4x screws for saw table (M8 x 16) (49)
• 4x washers for saw table (50)
• 4x foot caps (51)
• 1x push stick (52)
• 4x mounting bracket for attachment of the band
saw (53)
• Swivel part (54)
• Locking pin (c)
• Hexagon spanner - size 10/ 13
• Allen key, size 4
• Allen key, SW 5
• Original operating manual

4. Proper use

The band saw is used for the longitudinal and trans-
verse cutting of timbers or wood-like workpieces.
Round materials may only be cut using suitable hold-
ing devices (not included in the scope of delivery).
The machine may only be used in the intended man-
ner. Any use beyond this is improper.
The user/operator, not the manufacturer, is responsi-
ble for damages or injuries of any type resulting from
this.
Only saw bands that are suitable for the machine may
be used. An element of the intended use is also the
observance of the safety instructions, as well as the
assembly instructions and operating information in the
operating manual.
Persons who operate and maintain the machine must
be familiar with the manual and must be informed
about potential dangers. In addition, the applicable
accident prevention regulations must be strictly ob-
served. Other general occupational health and safe-
ty-related rules and regulations must be observed.
The liability of the manufacturer and resulting dam-
ages are excluded in the event of modifications of the
machine.
Despite use as intended, specific risk factors cannot
be entirely eliminated. Due to the design and layout of
the machine, the following risks remain:
• Hearing damage when the necessary hearing pro-
tection is not used.
• Harmful emissions of wood dusts during use in en-
closed areas.
• Risk of accident due to contact with the hands in the
uncovered cutting area of the tool.
• Danger of injury during a tool change (cutting haz-
ard).
• Danger due to the ejection of workpieces or parts
of the workpiece.
• Crushing of fingers.
• Danger due to kick-back.
• Tilting of the workpiece due to insufficient workpiece
support surface.
• Touching the cutting tool.
• Ejection of branches and workpiece parts.
• The machine may only be operated with original ac-
cessories and original tools from the manufacturer.
• Any use beyond this is improper use. The manufac-
turer is not responsible for the resulting damages;
the user solely bears the risk.
Please note that our equipment was not designed with
the intention of use for commercial or industrial pur-
poses. We assume no guarantee if the device is used
in commercial or industrial applications, or for equiv-
alent work.
www.scheppach.com GB | 35