Publicité
Les langues disponibles
Les langues disponibles
SNAP SHOW
- view/delete snapshots
!
By pressing the
and
the snapshots.
!
To delete the snapshot currently shown on the screen, press the left
—
button
[3 -
] and confirm by pressing the left button
[3 -
] again.
!
To delete all the snapshots saved on the mobile unit, press the door
release button
[5] and confirm by pressing the left button
—
[3 -
]..
Notes:
#
All snapshots are saved to the integrated ring memory. A maximum
of 100 snapshots can be saved. When the ring memory is full, the
oldest snapshots are overwritten automatically.
#
At the top left of the snapshot you can see the door intercom camera
from which it was saved (#1 or #2), what number image you are
looking at and the total number of images (e.g. 014/089). The
date and time at which the snapshot was saved are shown at the
bottom in the centre.
Factory setting: Restoring the factory settings deletes all the snapshots
DATE AND TIME
!
By pressing the
and
hours, minutes (e.g. 21:04), year, month and day (e. g. 2017 - 08
- 30) in succession.
!
Pressing the and [2] buttons changes the figure.
Notes:
#
The setting must be correct to get the exact date and time stamp on
the saved snapshots.
#
After a change of battery, the date and time must be reset.
Factory setting: not changed on reset
DOOR SET.
- Volume/duration of the ring tone on the door
intercom/duration of the door release
Notes:
#
When using two mobile units, the settings for the door intercom
must be the same.
#
When using two door intercoms, the settings apply to both
intercoms.
Volume
Setting for the ring tone volume on the door
intercom (1 to 9 bars)
Factory setting: 5 bars
Ring Time (s)
Setting for the duration of the ring tone on the door
intercom between 0 and 15 seconds. A setting of 0
seconds means that the ring tone is switched off.
Factory setting: 1 second
Unlock Time (s)
Setting for the duration of the door release relay
activation between 1 and 9 seconds
Factory setting: 3 seconds
LANGUAGE
Setting for the screen language
Factory setting: German
32 - GB
[2] buttons, you can scroll through
[2] buttons, you can change the
WALLPAPER
- background image
Setting for the screen background (choice of 3 images)
Factory setting: Image 1
—
REGISTER
- pairing/deletion of a door intercom
!
Move the hash # to the door intercom required.
To pair another door intercom (connected to the power supply)
!
press the left button
!
You now have approx. 20 seconds to press and hold the pairing
button [28] on the door intercom until you hear three short
beeps on the intercom as confirmation that pairing has been
successful. The mobile unit then makes a "plop" sound and the
start screen appears again.
To delete a door intercom
!
press the left button
!
then press the left button
Factory setting: no door intercom paired
Notes:
#
When a channel is paired with a door intercom, this is indicated by
the symbol
#
A maximum of two door intercoms can be paired with two mobile
units.
VERSION
The top two lines indicate the software version of the mobile unit; below
that is the version of door intercom #1 and (if present) #2.
RESET
Notes:
#
Resetting deletes all of the snapshots.
#
Following a reset, the door intercom is no longer paired with the
mobile unit.
#
The date and time are not affected by the reset.
!
To restore the factory settings, select "YES".
!
Then confirm by pressing the left button
14. Function of an optional signal
generator / optional door release
button
14.1 Optional signal generator
When the bell button [26] on the door intercom to which the signal
generator is attached is pressed, the signal generator is activated for
approx. 3 seconds.
14.2 Optional door release button
When the door release button is pressed, the door release that is
connected to the same door intercom as the door release button is
activated for the time set on the mobile unit.
—
[3-"
"]. The mobile unit beeps.
—
[3 - ] ,
—
[3 -
] again to confirm.
after the door intercom number (no. 1 or no. 2).
—
[3 -
].
Publicité
