Indexa DVT40 Set Mode D'emploi page 30

unit or the sound from the microphone [4] on the mobile unit
can be heard over the loudspeaker [18] on the door intercom in
alternation (intercom function).
#
—
Press the right button
the camera and save it on the mobile unit; the
appears briefly.
#
The talk function can be ended by pressing the on/off button
[8]; otherwise, it ends automatically after approx. 45 seconds,
the start screen appears again and the screen goes off after
approx. 20 seconds. Ending the talk function is indicated by a
quiet "plop" sound on the door intercom.
!
Opening the door:
If an electric door release is connected to the door intercom, it can be
activated by pressing the door release button
the camera image from the door intercom can be seen on the
monitor. Opening the door stops the ringing process and the talk
function, a quiet "plop" sound can be heard on the door intercom,
the start screen reappears on the mobile unit and the screen switches
off after approx. 20 seconds.
Notes:
#
In poor light conditions, the white LEDs [22] are activated by the
low light sensor [24]. The immediate area up to max. 0.8 m in front
of the door intercom is illuminated by this. Additional lighting must
be fitted to achieve a better image in the dark.
#
B
If: the mobile unit does not respond when the bell
button is pressed but the ring tone can be heard on the
door intercom
B
or no camera image is visible on the mobile unit when
operating with the power supply unit,
B
then: activate the mobile unit by pressing the on/off
button [8]
B
or reduce the distance between the mobile unit and
the door intercom.
If the system is still not working as expected, even when the devices
are next to one another, they must be paired again (see section
13.2 "Register").
#
The strength of the incoming wireless signal is displayed by the
symbol on the top right of the camera image on the screen [6].
The bars next to the antenna symbol indicate the strength.
#
A symbol on the top left of the camera image on the screen indicates
whether the door intercom showing the camera image is being
supplied with power by the power supply unit (
batteries ( ) .
#
If there is a ring on the intercom and a snapshot is saved but the
conversation is not accepted on a mobile unit, (at least) one new
snapshot is indicated by the flashing red
of the screen. As soon as the "Snap Show" menu item is selected,
the symbol disappears.
#
Transmission of sound is only available while the talk function is
activated.
30 - GB
[7] to take another static image on
symbol
[5] as soon as
) or by
symbol at the top left
11.2 Switching on the intercom camera image
manually
!
With the mobile unit switched on, press any button [1/2/3/5/7/8]
to make the start screen [6] appear.
!
—
Press the right button
paired door intercom, its camera image appears automatically;
with two paired intercoms, use the
the intercom required, confirm by pressing the left button
"Select"]and the camera image appears.
As long as the camera image is visible, the following options are
available:
!
To take a static image and save it on the mobile unit, press the right
—
button [7]; the symbol appears briefly.
!
By pressing the talk button [1], you can activate the talk function:
either the sound from the microphone [21] on the door intercom
can be heard over the loudspeaker [10] on the mobile unit or the
sound from the microphone [4] on the mobile unit can be heard
over the loudspeaker [18] on the door intercom in alternation
(intercom function).
The talk function can be ended by pressing the on/off button
[8]; otherwise, it ends automatically after approx. 45 seconds, the
start screen appears again and the screen goes off after approx. 20
seconds.
!
Pressing the door release button [5] activates a connected door
release, the start screen appears again and the screen switches off
after approx. 20 seconds.
!
To switch the camera off again, press the on/off button
otherwise, this happens automatically after approx. 45 seconds,
the start screen appears again and the screen switches off after
approx. 20 seconds.
Note:
When operating the door intercom with batteries, it is not possible to
switch the camera image on manually as the intercom is supplied in
energy-saving mode. "Monitor" appears on the black screen. (In
energy-saving mode, the camera image is displayed only when the ring
button [26] is pressed).
If you still wish to be able to switch the camera image on manually, you
have to switch the door intercom to energy consumption mode (please
note: in this case, the batteries in the intercom will go flat significantly
more quickly):
!
Press the pairing button [28] on the door intercom until you hear a
long beep.
!
Press the pairing button on the door intercom a second time until
you hear a long beep.
!
Press the pairing button a third time until you hear three short
beeps.
To return to energy-saving mode,
!
press the pairing button [28] on the door intercom until you hear
three short beeps.
[7 - "Mon" (Monitor)]. With only one
and [2] buttons to select
—
[3 -
[8];