Troubleshooting; Ec Declaration Of Conformity - Fimap FM43 ORB Manuel D'utilisation Et D'entretien

This chapter lists the most common problems linked with the use of the appliance. If you are unable to resolve the problems with the
information given here, please contact your nearest assistance centre.
PROBLEM
THE APPLIANCE DOES NOT SWITCH ON
INSUFFICIENT DETERGENT SOLUTION
ON THE PAD HOLDER
The undersigned manufacturer:
FIMAP S.p.A.
Via Invalidi del Lavoro n.1
37050 Santa Maria di Zevio (VR) - Italy
declares under its sole responsibility that the products
SINGLE DISC MACHINE mod. Orbitale FM43 ORB
comply with the requirements of the following Directives:
• 2006/42/EC: Machinery Directive.
• 2006/95/EC: Low Voltage Directive.
• 2004/108/EC: Electromagnetic Compatibility Directive.
They also comply with the following standards:
• EN 60335-1: Household and similar electrical appliances - Safety.
Part 1: Generic standards.
• EN 60335-2-67: Household and similar electrical appliances. Part
2: Specific norms for automatic machines for floor treatment for
commercial and industrial use.
• EN 12100-1: Machine safety
fundamental principles of design - Part 1: Basic terminology and
methodology.
• EN 12100-2: Machine safety
fundamental principles of design - Part 2: Technical principles.
• EN 55014-1: Electromagnetic compatibility - Regulations for
household appliances, electrical devices and similar equipment.
Part 1: Emission - Regulation for product family.

TROUBLESHOOTING

POSSIBLE CAUSE
The power cable extension is not connected
to the mains socket.
The power cable extension is not connected
to the appliance's power cable.
The electrical specifications of the appliance
should correspond to
specifications of the power supply network.
Extension cable damaged.
Overheating of the brush head motor.
The amount of detergent in the solution tank
is insufficient for the work that needs doing.

EC DECLARATION OF CONFORMITY

•
•
•
•
The person authorised to compile the technical file:
Mr. Giancarlo Ruffo
FIMAP S.p.A.
Via Invalidi del Lavoro n.1
37050 Santa Maria di Zevio (VR) - Italy
Santa Maria di Zevio (VR) Italy, 30/06/2015
- Fundamental concepts,
- Fundamental concepts,
32
Check that the plug on the extension cable
has been inserted into the mains supply
socket.
Check that the plug on the cable of the
appliance has been inserted into the socket
on the extension cable.
Make sure that the electrical specifications
of the appliance correspond to the electrical
the electrical specifications of the power supply network,
check the technical information on the serial
number plate.
Check the extension cable is not damaged,
and if it is, replace it.
Make sure that the thermal breaker on the
back of the handlebar has not tripped. If it
has, wait a few minutes until it has cooled
down, then press the specific circuit breaker
button to reactivate the power supply and
motor operation
Make sure that the amount of detergent
solution in the solution tank is sufficient for
the work to be carried out, and if necessary
fill the solution tank.
EN 55014-2: Electromagnetic compatibility - Regulations for
household appliances, electrical devices and similar equipment.
Part 2: Immunity - Regulation for product family.
EN 61000-3-2: Electromagnetic compatibility (EMC) - Part 3-2:
Limits – Limits for harmonic current emissions (Equipment with
input current 16 A per phase).
EN 61000-3-3: Electromagnetic compatibility (EMC) - Part 3-3:
Limits – Restriction of voltage variations and flicker in low voltage
power supply systems for devices with a rated current 16 A.
EN 62233: Household and similar electrical appliances -
Electromagnetic fields - Methods for evaluation and measurement
SOLUTION
FIMAP S.p.A.
Legal representative
Giancarlo Ruffo