Master BP 13 Manuel D'utilisation Et De Maintenance page 43

►► 6. CLEANING AND CARE
►
BG
► Wipe off powder coated surfaces with soft, moist rag.
BY
Do not clean heater with cleaners that are combustible or
corrosive.
CZ
► Remove debris from the burner to keep it clean and
safe for use.
► Cover the burner unit with the optional protective cover
EE
when the heater is not in use.
HR
►► 7. ASSEMBLY PARTS
►
HU
TOOLS NEEDED:
► Open end wrench 10 & 13 mm
► Adjustable opening wrench (2) 20 cm long
LT
► Slip joint pliers 23 cm long
► Philips screwdriver w/ medium blade
LV
► Spray bottle of soap solution for leakage test
RO
PARTS SUPPLIED:
► Stand with LPG cylinder housing and 3 post brackets.
► 9 Cup Nuts (M6 mm), 9 Small Screws (M6 x 10 mm), 9
GB
Small Flat Washers (Ø 6 mm) for Reflector Assembly.
► 6 Large Bolts and Flange Nuts (M6) for Support Legs/
SI
Main Pole Assembly.
► 3 Medium Bolts (M8 x 15 mm) for Support Legs/Stand
SK
Assembly.
► 3 Reflector Spacers and Wing Nuts, 9 Large Flat Wash-
ers for Reflector and burner Assembly.
UA
► 3 pcs ground fixer
► 6 pcs M6 x 10 mm ground fixer bolts & nuts
SE
ASSEMBLY PROCEDURES (APPENDIx I)
SI
STEP 1 (FIG. 4)
1-1. Put the 3 pcs post brackets on each position on the
base as shown in the picture.
SK
1-2. Use 3 Medium Bolts(M8x15) to join the post brackets
and stand.
STEP 2 (FIG. 5)
2-1. Put the post on the top of 3 pcs post brackets.
2-2. Use 6 Large Bolts and Flange Nuts (M6) to connect
the post to the
3 pcs post brackets. Tighten the bolts and nuts.
STEP 3 (FIG. 6)
Place the tank housing on the stand.
STEP 4 (FIG. 7)
4-1. Remove the 4 bolts from the burner.
4-2. Put the gas hose through into the post.
4-3. Fix the burner unit to the post by the 4 bolts.
STEP 5 (FIG. 8)
5-1. Check whether the connection of vertical post and
burner are assembled according to instructions, and all
bolts and nuts are tightened.
5-2. Put 6 pcs Large Flat Washers on 3 Reflector Spacers.
STEP 6 (FIG. 9)
Fasten the reflector with 3 pcs Large Flat Washers and 3
pcs Wing Nuts.
STEP 7 (FIG. 10)
7-1. Bring up the tank housing and rest it on the post plate.
7-2. Connect the regulator to the gas tank and tighten it
with adjustable wrench.
7-3. Connect the end thread of inlet gas hose to the regula-
tor.
7-4. Put LPG gas tank on the stand.
PARTS AND SPECIFICATIONS (APPENDIx II)
FIG. 11
I. Reflector
II. Flame screen
III. Burner base
IV. Air admittance fence
V. Gas valve controller
VI. Base of control housing
VII. Post
VIII. Tank housing
IX. Post bracket
X. Stand
►► 8. PROBLEMS CHECK LIST
►
PILOT WILL NOT LIGHT
► PROBABLE CAUSE
1. Gas valve may be OFF
2. Tank fuel empty
3. Opening blocked
4. Air in supply system
5. Loose connections
► SOLUTION
1. Turn the gas valve ON
2. Refill LPG tank
3. Clean or replace opening
4. Purge air from lines
5. Check all fittings
PILOT WILL NOT STAY ON
► PROBABLE CAUSE
1. Debris around pilot
2. Loose connections
3. Thermocouple Bad
4. Gas leak in line
5. Lack of fuel pressure
► SOLUTION
1. Clean dirty area
2. Tighten connections
3. Replace thermocouple
4. Check connections
5. Tank near empty. Refill LPG tank.
BURNER WILL NOT LIGHT
► PROBABLE CAUSE
1. Pressure is low
2. Opening blocked
3. Control not ON
4. Thermocouple Bad
5. Pilot light assembly bent
6. Not in correct location
► SOLUTION
1. Tank near empty. Refill LPG tank.