Chicco oasys 2-3 FixPlus Evo Mode D'emploi page 21

he passenger sitting in the seat directly behind it
and adjusting the backrest to the most vertical
ith position. If the vehicle is fitted with an adjuster
ety to regulate the height of the safety belt, posi-
on tion it as low as possible. Check that the safety
belt adjuster is behind (or at the most aligned)
int with the backrest of the vehicle seat (Fig. 5A
and 5B).
It is not recommended to fit the child car seat
RE-
into a front seat equipped with airbag. If you
CT
wish to fit the child car seat in any seat protect-
ed by airbag, always refer to the vehicle instruc-
ui- tions manual.
car Make sure that the buckle seat belt is not too
ev- high and not rests on the armrest of the car
seat (Fig 3). Otherwise, try to install the car seat
om for your child on another car seat in the car.
INSTRUCTIONS FOR USE
at-
CONTENTS
to
ent • F itting the child car seat inside the vehicle
using safety belts and placing the child inside
is • F itting the child car seat inside the vehicle
in using safety belts and rigid FixPlus clasps and
car placing the child inside
ust • H ow to position SAFE PAD
ou • I nstalling the child seat inside the vehicle
not without the child inside
he • H ow to remove the child from the child car
on seat
• R emoval of the child car seat from the vehicle
ont • H ow to remove and reinstall SAFE PAD
ays • I nstalling and removing the cup holder
his • A djusting the height of the back rest
ng • A djusting the width of the back rest
• A djusting the inclination of the child car seat
tis- backrest/seat
ally • R emovable backrest/seat covers
m- • C leaning and maintenance of the seat covers
ear
PARTS
ear
int A. Headrest
to B. Diagonal belt guide
eat C. Backrest
D. Armrests
of E. Seat
t is F. Lap belt guide
ch G. Cup holder
he H. Reclining adjuster button
I. Safety belt guide open/close button
J. Cup holder clip
K. Backrest width adjuster wheel
L. Backrest height adjuster lever
M. Rear pocket for instruction booklet
N. Side wings
O. Rigid FixPlus clasp lever
P. Rigid clasps
Q. Indicators
R. Rigid clasp release system buttons
S. Safe Pad
FITTING THE CHILD CAR SEAT INSIDE
THE VEHICLE USING SAFETY BELTS AND
PLACING THE CHILD INSIDE
WARNING! These instructions and diagrams
are for the installation of the child car seat on
the right back seat.
To fit the child car seat in other positions, carry
out these operations in the same order.
1. P lace the child car seat onto the vehicle seat
with the backrest up against the vehicle seat
backrest.
WARNING! Check that the vehicle headrest
does not interfere with the child seat headrest:
it must not push it forwards (Fig. 6). If this hap-
pens, remove the headrest from the vehicle
seat where you intend to install the child car
seat. Remember to replace the vehicle head-
rest when the child car seat is removed and a
passenger uses the seat.
WARNING! The rear side of the child car seat
must be resting against the vehicle seat.
2. P lace your child inside the car seat with his
back correctly placed against the backrest.
3. C heck the backrest height (see paragraph
"ADJUSTING THE HEIGHT OF THE BACKREST")
4. C heck the backrest width (see paragraph
"ADJUSTING THE WIDTH OF THE BACKREST")
5. T hread the diagonal car seat belt through the
diagonal belt guide (B). Check that the belt
guide (l) open/close button is firmly closed;
you must be able to see the white reference
line (Fig. 7).
6. O pen SAFE PAD (S) (Fig. 8). Insert the car seat
belt in SAFE PAD, positioning it in the guides
(Fig. 9) and then close the two ends (Fig.10),
making sure that both pieces of velcro are
correctly fastened.
21