Setting The Work Depth; Working Instructions; Working With The Scarifier - ATIKA VT 32 Z Notice Originale

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 24
S
S
w
w
i
i
t
t
c
c
h
h
i
i
n
n
g
g
o
o
n
n
/
/
o
o
f
f
f
f
Do not use any device where the switch can not be switched
on and off. Damaged switches must be repaired or replaced
immediately by the customer service.
The device is equipped with a safety circuitry preventing
inadvertent switching on.
Start the device only after you have placed it on a low-growth lawn
area.
Switching on
Tilt the scarifier slightly towards you so that the front wheel are
above the ground.
Push the safety button and keep it depressed.
Next, pull the switch lever toward the handle hoop.
The scarifier starts and the scarifier drum can rotate freely.
Now release the safety button.
Switching off
When you release the switch lever it returns automatically to its
original position.
Motor protection
The motor is equipped with a protective circuit breaker and
switches off automatically in case of overloading. After a cooling-
down break (approx. 15 min), the motor may be restarted.
Release the switch lever because the device will otherwise
restart immediately after it has cooled down. Risk of injury!
S
e
t
t
i
n
g
S
e
t
t
i
n
g
Before settings the work depth:
− switch off device
− wait until the drum is stationary
Adjust the working height by pushing the height
adjustment switch (21) to your desired position.
Position
Scarifier
1
2
3
4
Set the work depth according to the grass and ground
conditions at both running wheels.
Recommended work depths:
Regularly scarified soft ground; without stones
Seldom scarified mossy ground; with stones
Uncultivated very mossy; with stones
If the scarifying blades are worn, adjust lower by 1-2 levels.
Set a lower work depth when the motor is straining (motor
speed drops and motor noise changes).
Example: Work depth set to 4
20
t
h
e
w
o
r
k
d
e
p
t
h
t
h
e
w
o
r
k
d
e
p
t
h
Work depth
Lawn aerator
4,0 mm
0 mm
-6 mm
-10,0 mm
change to 3
Before commencing work, ensure the following:
You may not start to operate the machine until you have read
these operating instructions, observed all the instructions given
and installed the machine as described!
Provide for a safe and cleaned workplace. Remove from the
working area objects which might be thrown off.
Before starting your work make sure that:
− the tools and bolts are not worn or damaged. To avoid any
unbalance worn or damaged tools and bolts must only be
replaced as a whole set.
− drum and blades are in proper condition (see "blade
replacement")
− all screw connections are tight
− no other persons or animals stay within the working area,
− you can always step back without any barriers,
− you have always a secure standing position.
Always keep your hands and feet at a safe distance to
the rotating tool.
Vibration
If persons who have blood circulation problems are too often
exposed to vibrations damages to the nervous system or to blood
vessels may occur.
You can reduce vibrations
-
by thick and warm working gloves,
-
shorter working time (have longer breaks).
See a doctor if your fingers swell, you don't feel well or your fingers
become numb.
Scarifying
Using the scarifier drum, the device can be used as scarifier
to remove mats and mosses in the lawn and to cut through wild
growth with low roots.
To enable the growth of a healthy lawn in spring, the absorption of
10 mm
water, air and nutrients in the root area needs to be increased. We
6 mm
recommend scarifying the lawn in spring and autumn.
1 mm
To achieve good results and to extent the life of the scarifier drum,
-4,0 mm
the lawn should be mowed before scarifying (shorter than 4 cm).
Do not scarify when the lawn has been freshly sown or when
it is wet or too dry.
Position
• Place the scarifier at the edge of the lawn near the receptacle.
3-4
Move the cable after each turn to the opposite already
2-3
scarified side.
• Select the work depths according to the condition of the lawn
1-2
(see "Setting the work depth").
• Make sure not to place excessive strain on the scarifier.
In case of excessive strain, the motor speed drops and
the motor noise changes.
W
o
r
k
i
n
g
i
n
s
t
r
u
c
W
o
r
k
i
n
g
i
n
s
t
r
u
c
W
o
r
k
i
n
g
w
i
t
h
t
h
e
s
W
o
r
k
i
n
g
w
i
t
h
t
h
e
Stop and release the switch lever
Wait until the scarifier drum stands still
Set a lower work depth
t
i
o
n
s
t
i
o
n
s
c
a
r
i
f
i
e
r
s
c
a
r
i
f
i
e
r

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Vt 3200001020000

Table des Matières