Machine Specifications; Technical Data; Machine Description; Transport And Installation - Jet AP-0 Mode D'emploi

The arbor press is designed to
operate in closed rooms, and must
be bolted to a solid work bench or
table securely attached to the floor.
Keep the floor around the machine
clean and free of scrap material,
oil and grease.
Remove all loose clothing and
confine long hair.
Before operating the machine,
remove tie, rings, watches and
other jewellery.
Wear safety shoes; never wear
leisure shoes or sandals.
Sheet metal stock has sharp
edges.
WEAR GLOVES when handling
sharp edged work pieces.
WEAR SAFETY GLASSES.
KEEP HANDS AND FINGERS
clear of the pressing area in front
and rear of the ram.
Stay alert!
Give your work undivided
attention. Use common sense. Do
not operate the machine when you
are tired.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine under
the influence of drugs, alcohol or
any medication. Be aware that
medication can change your
behaviour.
Keep children and visitors a safe
distance from the work area.
Keep guards in place and in
working order.
Specifications regarding the
maximum pressing force must be
observed.
Do not overload the press by using
handle extensions (cheater bars)
Work must be mounted on the
press securely. Do not use the
press with work mounted at an
angle.
The press is designed for pressing,
broaching, bending and
straightening purposes only.
Always make sure the ram
contacts the workpiece squarely
before applying pressure.
Some parts may have a tendency
to pop out of the press or explode
under pressure. Protect yourselves
accordingly.
Support long work pieces with
helping roller stands.
Do not stand on the machine.

4. Machine specifications

4.1 Technical Data

AP-0:
Throat
Working height above table
Tons pressure
Ram Bore
Basic size (LxWxH) 240x100x250mm
Weight
AP-1:
Throat
Working height above table
Tons pressure
Ram Bore
Basic size (LxWxH) 275x125x305mm
Weight
AP-2:
Throat
Working height above table
Tons pressure
Ram Bore
Basic size (LxWxH) 430x160x410mm
Weight
AP-3:
Throat
Working height above table
Tons pressure
Ram Bore
Basic size (LxWxH) 460x215x550mm
Weight
AP-5:
Throat
Working height above table
Tons pressure
Ram Bore
Basic size (LxWxH) 660x250x860mm
Weight

4.2 Machine Description

4
A...Ram
85mm
B....Ram guide adjust bolts
100mm
0,5t
C....Arbour press body
Ø9,5mm
D...Pinion oil hole
8,5kg
E...Press handle
F....Support plate
102mm
G....Bolt down holes
125mm
1t
H....Pinion
Ø9,5mm

5. Transport and installation

10,5kg

5.1 Transport

For transport use a forklift or hand
145mm
trolley. Make sure the machine
145mm
does not tip or fall off during
2t
transport.
Ø12,7mm
If you notice transport damage
28kg
while unpacking, notify your
supplier immediately. Do not
operate the machine!
137mm
290mm Dispose of the packing in an
3t environmentally friendly manner.
Ø12,7mm
Clean all rust protected surfaces
with petroleum, diesel oil or a mild
45kg
solvent.
Coat all machined surfaces with a
216mm
light coat of oil to inhibit rust.
460mm
5t

5.2 Installation

Ø12,7mm
The arbor press is designed to
operate in closed rooms, and must
140kg
be bolted to a solid work bench or
table securely attached to the floor.

5.3 Initial Lubrication

See chapter 8 for lubrication.

6. Machine operation

Specifications regarding the
maximum pressing force must be
observed.
Do not overload the press by using
handle extensions (cheater bars)
Fig 1