Remaining Hazards; Machine Specifications; Technical Data - Jet JMD-3 Mode D'emploi

Keep this operating instruction close
by the machine, protected from dirt
and humidity, and pass it over to the
new owner if you part with the tool.
No changes to the machine may be
made.
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this case,
protect the machine by unplugging the
power cord.
Remove all loose clothing and confine
long hair.
Before operating the machine, remove
tie, rings, watches, other jewellery,
and roll up sleeves above the elbows.
Wear safety shoes; never wear leisure
shoes or sandals.
Always wear the approved working
outfit
- safety goggles
- ear protection.
Do not wear gloves.
Install the machine so that there is
sufficient space for safe operation and
work piece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be bolted to
the cabinet stand or a solid work
bench.
Make sure the machine cannot tip.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense. Do not operate
the machine when you are tired.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended.
Before you leave the workplace switch
off the machine.
Keep children and visitors a safe
distance from the work area.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Work only with well sharpened tools.
Always close the chuck guard and
pulley cover before you start the
machine.
Remove the chuck key and wrenches
before machine operation.
Specifications regarding the maximum
or minimum size of the work piece
must be observed.
Do not remove chips and work piece
parts until the machine is at a
standstill.
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
Never place your fingers in a position
where they could contact any rotating
tool, chuck or cutting chips.
Secure work piece against rotation.
Use fixtures, clamps or a vice to hold
the work piece.
Never hold the work piece with your
hands alone.
When using a vice, always fasten it to
the table.
Never do any works "freehand" (hand-
holding the work piece rather than
supporting it).
Never move the head while the
machine is running.
If a work piece overhangs the table
such that it will fall or tip if not held,
clamp it to the table or provide
auxiliary support.
Check the save clamping of the work
piece before starting the machine.
Remove cutting chips with the aid of
an appropriate chip hook when the
machine is at a standstill only.
Never stop the rotating chuck or tool
with your hands.
4
Measurements and adjustments may
be carried out when the machine is at
a standstill only.
Setup work may only be carried out
after the machine is protected against
accidental starting by pressing the
emergency stop button.
Maintenance and repair work may
only be carried out after the machine
is protected against accidental starting
by pulling the mains plug.
Do not use wire wheels or grinding
wheels on this machine.
Choose a low speed for tapping.
Tapping speed is limited to 500rpm.
If machine is not in use, turn off main
switch.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist.
The rotating chuck, tool and cutting
chips can cause injury.
Thrown and hot work pieces and
cutting chips can lead to injury.
Chips, dust and noise can be health
hazards. Be sure to wear personal
protection gear such as safety
goggles, dust mask and ear
protection.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.

4. Machine specifications

4.1 Technical data

Drilling capacity steel St37
Tapping capacity steel St37
Milling capacity of face mill
Milling capacity of end mill
Spindle to column
Distance table to spindle max 410mm
Spindle taper
Draw bar
Spindle travel
Head tilt
Spindle speeds
Max travel X-axis
Max travel Y-axis
Table size
T-slots 3
Overall 700 x 560 x 850mm
Net weight
20mm
M10
50mm
20mm
230mm
MT-3
M12
70mm
90°L /45°R
100-1750rpm
350mm
150mm
160 x 510mm
12mm
165 kg