Know Your Product; Operation - SPARKY HP Professional R 10E Notice Originale

purpose. Any use other than those mentioned
in this Manual will be considered a case of
misuse. The user and not the manufacturer
shall be liable for any damage or injury result-
ing from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised
at all times if they are in the area in which the
tool is being used. It is also imperative that
you observe the accident prevention regula-
tions in force in your area. The same applies
for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
▪ The power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
liquids and gases. The working place should
be well lit.

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Two-jaw chuck for taps
2. Locking pin for fixing the chuck
3. Chuck key
4. ON/OFF switch
5. Lock-on button
6. Auxiliary handle
7. Depth gauge
8. Wing screw for adjusting the depth gauge
9. Ventilation slots
10. Tap (not included in the delivery)

Operation

This power tool is supplied from single-phase
alternating current mains only. It is double
in¬sulated according to EN 60745-1 and IEC
60745 and can be connected to grounded or not
grounded sockets. This power tool is radio sup-
6
EN
pressed in compliance with EMC Directive.
This power tool is designed for cutting inner
right-hand threads M4 - M10 in metalware. It is
equipped with a changeover gear for automatic
reversing after the thread has been cut and with
electronic switch for smooth rpm adjustment.
PRIOR TO INITIAL OPERATION
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
▪ In case the work area is remote from the pow-
er source, use as short as practicable exten-
sion cord with proper cross-section.
▪ Check that the auxiliary handle is properly
mounted and reliably tightened.
SWITCHING ON - SWITCHING Off
Brief activation
▪ Switching on: Press ON/OFF switch 4.
(Fig. 1)
▪ Switching off: Release ON/OFF switch 4.
Continuous operation
▪ Switching on: Press ON/OFF switch 4 and in
pressed position lock it by button 5. (Fig. 2)
▪ Switching off: Press ON/OFF switch 4 once
and release it immediately.
NSERTING AND fASTENING TAPS
I
(fig. 3)
In order to insert the tap 10 into the chuck 1,
loosen the chuck jaws by rotating the chuck key
3 anti-clockwise. Insert the tap so that its square
shaft enters the square opening in the chuck 1,
R 10E